Mercedes-Benz Comand MY11 Скачать руководство пользователя

Страница: 105 / 194

slide

XVY

press

pressing the

button and

using the telephone keypad on COMAND

pressing the

button on the

multifunction steering wheel

using Voice Control (see the separate Voice

Control operating instructions)

Unless stated otherwise, the descriptions and

illustrations in this section refer to COMAND.

Function restrictions

The telephone is not ready for use in the

following situations:

the telephone automatically tries to log on

to a network. If no network is available, you

will not be able to make a "911" emergency

call. If you attempt to make an outgoing

call, the

No Service

message will appear

for a short while.

911 emergency call

WARNING

The 911 emergency call system is a public

service. Using it without due cause is a

criminal offense.

The following requirements must be fulfilled

for a 911 emergency call:

the mobile phone must be switched on.

a network must be available.

a valid and operational SIM card must be

inserted in the mobile phone.

the mobile phone is connected to COMAND

via Bluetooth

If you cannot make an emergency call, you

must arrange rescue measures yourself.

Enter numbers on COMAND (

page 108).

Press the

button.

The telephone makes the connection.

Wait for the emergency call center to

respond and then describe the emergency.

Telephony via the Bluetooth

interface

Conditions

On the mobile phone

For telephony via COMAND's Bluetooth

interface, a Bluetooth

-capable mobile

phone is required.

Not all mobile phones available on the

market are equally suitable. More detailed

information on suitable mobile phones and

on connecting Bluetooth

-capable mobile

phones with COMAND can be found on the

Internet at

http://www.mbusa-mobile.com. Or call

the Mercedes-Benz Customer Assistance

Center at

1-800-FOR-MERCedes(1-800-367-6372)

(for the USA) or Customer Relations at

1-800-387-0100 (for Canada).

The battery of the mobile phone should

always be kept sufficiently charged in order

to prevent malfunctions.
In preparation for telephoning via the

Bluetooth

interface, you should check the

following items on your mobile phone (see the

mobile phone operating instructions):

Hands-Free Profile

The mobile phone must support Hands-

Free Profile 1.0 or above.

Some displays (e.g. the signal strength)

depend on the supported version of the

Hands-Free Profile.

Bluetooth

visibility

On certain mobile phones, the device itself

must be made "visible" for other devices,

as well as activating the Bluetooth

Telephony via the Bluetooth

interface

103

Telephone

Содержание Comand MY11



































































































































































































Результаты поиска

Содержание Comand MY11

Отзывы:

Похожие инструкции для Comand MY11

Бренды по названию

Популярные бренды

Mercedes-Benz Comand MY11, Руководство по эксплуатации

Результаты поиска

Содержание Comand MY11

Отзывы:

Похожие инструкции для Comand MY11

Бренды по названию

Популярные бренды