mensor CPC4000 Скачать руководство пользователя страница 91

Страница: 91 / 114

Operating Instructions - CPC4000

Industrial Pressure Controller

CPC4000

8.6 Automatic Contamination Prevention System

The Automatic Contamination Prevention System (Automatic CPS) is connected between the device

under test and the Measure/ Control port of the instrument by the backplate located on the rear panel

(Figure 8.6-B). The primary function of the Automatic CPS is to prevent liquid and particulate contami-

nents from entering into the instrument. The Automatic CPS (Figure 8.6-A) is designed to interface with

the CPC4000 and is energized to purge the device under test of any contaminents by an automated

purge sequence within the CPC4000 user interface.

Figure 8.6-A -

Automatic Contamination Prevention System

Automatic CPS Backplate

Figure 8.6-B - Rear

Panel with Automatic CPS Backplate

Warning

Warning! The pressure connections must be installed according to the following

instructions, observing the relevant regulations. The installation is to be per-

formed by trained, authorized personnel, knowledgeable in the safety regulations

for working on pneumatic/hydraulic systems

Warning

Warning! The Automatic CPS should only be used to decontaminate the system

for liquid or particulate contaminents that are non reactive, non corrosive and

non explosive.

Содержание CPC4000



















































































































Результаты поиска

Содержание CPC4000

Отзывы:

Похожие инструкции для CPC4000

Бренды по названию

Популярные бренды

mensor CPC4000, Руководство по эксплуатации

Результаты поиска

Содержание CPC4000

Отзывы:

Похожие инструкции для CPC4000

Бренды по названию

Популярные бренды