mensor CPC4000 Скачать руководство пользователя страница 23

Страница: 23 / 114

Operating Instructions - CPC4000

Industrial Pressure Controller

CPC4000

5.3 Mounting
The instrument can be set up on a desk top or it can be rack-mounted. Rack mount hardware is optional

on the CPC4000 (see Section 5.2 Dimensions and Section 8, Options).
The special transducers used in the CPC4000 are relatively insensitive to tilt and vibration. However to

further assure stability and accuracy, avoid mounting the instrument on surfaces subject to excessive mo-

tor or machinery vibration.
5.4 Rear Panel
Five pneumatic pressure ports are located across the rear panel. Any instrument containing sub-atmo-

spheric pressure ranges needs a vacuum pump to be connected at the exhaust port. The instruments

with pressures above or at atmospheric pressures will have the exhaust port open. Next to the ventila-

tion fan is a 10-32 UNF fitting which is connected to the barometric reference if installed. Positioned on

the right side is a remote communication connections; RS-232, Ethernet, IEEE- 488, USB along with the

USB host connection.

Figure 5.4 A – Rear Panel

5.4.1 Pressure Connections

Warning

Warning! The pressure connections must be installed according to the following

instructions, observing the relevant regulations. The installation is to be per-

formed by trained, authorized personnel, knowledgeable in the safety regulations

for working on pneumatic/hydraulic systems.

Notice

Five pressure connections are on the rear panel. Plugged connections are not used.

All pressure ports on the rear apart from the Vent Port are female 7/16 - 20 SAE/MS straight threads per

MS16142 and SAE J514 table 14. Connected adaptors require a tube fitting boss seal with an o-ring per

MS33656. Mensor can provide a variety of adapter fittings (see Section 8 Options) with the instrument.

Do not use sealant on fittings sealed with an o-ring. The integrity of each seal is particularly important

since even microscopic leaks can cause errors in pressure measurements.

Содержание CPC4000



















































































































Результаты поиска

Содержание CPC4000

Отзывы:

Похожие инструкции для CPC4000

Бренды по названию

Популярные бренды

mensor CPC4000, Руководство по эксплуатации

Результаты поиска

Содержание CPC4000

Отзывы:

Похожие инструкции для CPC4000

Бренды по названию

Популярные бренды