Mendota FV44i-0616, Инструкция по установке и эксплуатации

Страница: 27 / 58

Burner Orifices
#65-14-00054[54 DRILL]
#65-14-00055[55 DRILL]
Motorized
LP Pressure
Regulator
[10.0-5.5"WC]
# 907.012
55
54
CONVERTING INSERT FOR LP GAS
Kit # HA-58-00302 for Mendota Model FV-44i
This conversion kit shall be installed by a qualified service agency in
accordance with the manufacturer’s instructions and all applicable codes and
requirements of the authority having jurisdiction. If the information in these
instructions is not followed exactly, a fire, explosion or production of carbon
monoxide may result causing property damage, personal injury or loss of life.
The qualified service agency is responsible for the proper installation of this kit.
The installation is not proper and complete until the operation of the converted
appliance is checked as specified in the owner instructions supplied with the
kit.
Caution : The electrical supply to the fireplace must be turned off prior
to performing the conversion. The gas supply must be shut off prior to
disconnecting the electrical power.
Orifice Size Requirement
A Natural Gas to LPG conversion kit #HA-58-00302 must be ordered
and installed to convert the FV-44i Fireplace to burn LPG.
LP Conversion Kit # HA-58-00302 contains the following parts: One Motorized LP Pressure Regulator #907.012 and two
Cap Orifices (
drill #54 and drill #55) .
Procedure to Convert
Insert for
LP
Gas
This Fireplace Insert arrives from the factory ready to burn Natural Gas. If you intend to burn LPG, it is highly
recommended that you convert this fireplace
's
Pressure Regulator, Pilot Orifice
Slider
and Burner Orifices prior to
placing this fireplace in its fireplace cavity.
See diagrams, on this page, and follow these instructions to prepare this fireplace for conversion to LPG.
WARNING: It is of the utmost importance that the correct burner orifices be installed for both the rear and
front burners.
1. Turn off gas supply at the appliance service valve.
Remove the access
panel on the left side off the insert to access the valve.
2. See diagrams on this page and identify the Pressure Regulator on the Valve
Body.
3. Using a Torx T20 or a slotted screwdriver, remove 2 screws that secure the
NG Pressure Regulator to the gas valve body and remove NG Pressure
Regulator, see
next
page.
4. Install the new LP Pressure Regular onto the gas valve body in the same
position and orientation as the NG Pressure Regulator you removed in Step
2,
above. The LP Pressure Regulator can only be mounted in one position.
Secure the LP Pressure Regulator in place. Tighten down.
See next page for detailed instructions.
VIEW FROM FIREBOX
PRESSURE REGULATOR
PAGE 23
This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions
and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions
is not followed exactly, a fire, explosion or production of carbon monoxide may result causing property damage, per-
sonal injury or loss of life. The qualified service agency is responsible for the proper installation of this kit. The in-
stallation is not proper and complete until the operation of the converted appliance is checked as specified in the
owner instructions supplied with the kit.
Cet équipement de conversion sera installé par une agence qualifiée de service conformément aux instructions du fabricant et
toutes exigences et codes applicables de l'autorisés avoir la juridiction. Si l'information dans cette Instruction n'est pas suivie
exactement, un feu, explosion ou production de protoxyde de carbone peut résulter le dommages causer de propriété, perte ou
blessure personnelle de vie. L'agence qualifiée de service est esponsable de l'installation propre de cet équipement.
L'installation n'est pas propre et complète jusqu'à l'opération de l'appareil converti est chèque suivant les critères établis dans les
instructions de propriétaire provisionnées avec l'équipement.