Mendota DT3-PF2-LX, Инструкция по установке и эксплуатации

Страница: 16 / 65

15
GENERAL INSTALLATION INSTRUCTIONS
CAUTION: Each installation must conform to all local, state and national codes. Refer to the national fuel gas code and local zoning
and code authorities for details on installation requirements. The Mendota Fireplace must be vented to the outside in accordance
with the latest edition of the National Fuel Gas Code. In the absence of local codes, the installation must conform to the most cur-
rent edition of the National Fuel Gas Code ANSI Z223.1, also known as NFPA 54. NOTE: The Mendota DXV Fireplace is approved
for mobile home and bedroom installations.
CAUTION: The Mendota DXV Fireplace may be installed in a manufactured (mobile) home after the first sale of the home. Manu-
factured home (mobile home) installation must conform with the Manufactured Home Construction and Safety Standard, Title 24
CFR, Part 3280, or, when such a standard is not applicable, the Standard for Manufactured Home Installations, ANSI A225.1/NFPA
501A, or CSA Z240.4-Gas Equipped Mobile Housing. Consult your local building official. Note: For mobile home installations unit
must be bolted to the floor and properly grounded.
1.
After selection of the desired fireplace location, prepare the rough opening using framing dimensions on PAGE 164.
Be sure to also prepare opening to allow for co-axial vent (see "Flue Venting Instructions".
2. Check to make certain all venting requirements and clearances are being followed.
3. The Fireplace is designed to be installed into rough framing. The drywall will cover the adjustable nailing flanges on
the Fireplace sides. Before sliding the Fireplace into the framed opening, adjust the nailing flanges to accommodate
the thickness of the wall material.
NOTE : FRAMING MATERIALS LOCATED ABOVE FIREPLACE BODY MUST
MAINTAIN CORRECT CLEARANCES TO VENT PIPE.
WARNING
DO NOT COVER THE 2” BLACK FRONT SURFACE OF THIS UNIT IF YOU INTEND TO USE THE ANDOVER,
BENTLEY, DEERFIELD or WELLINGTON TRIMS!!
4. Slide Fireplace into the rough framed opening. When finishing the unit, combustible materials may overlay nailing
flanges and come in contact with the edges of the black front surface, but may not overlap the 2" black front surface.
Noncombustible material, such as marble, stones or brick, can be installed over the 2" black surface,
only if you
are certain that a Deerfield Front, Andover Front, Bentley Front, Prairie Front or a Wellington Front is NOT
going to be used as the optional trim
, up to the inside edge of black frame (next to glass). ROUGH FRAMING
CAN COME NO CLOSER TO UNIT THAN THE STAND-OFFS.
5. Level the Fireplace and secure into opening by nailing through the nailing flanges on cabinet side panels. Holes are
provided in fireplace floor behind grill to secure fireplace to floor using lag screws or drywall screws, if required.
NOTE: A removable panel in the enclosure for future visual inspection of flue connection is recommended.
6. Have an electrician install a 115-Volt supply to the junction box on lower left side of the fireplace cabinet. Connect
wires to the duplex outlet. This duplex outlet is removable from outside of cabinet for easy wiring. Make sure the
outlet is properly grounded and that the installation conforms to all local and national wiring codes.
7. Have gas supplier or qualified plumber install gas supply line to fireplace and connect to gas nipple. Be sure Gas
Supply Requirements (see PG. 9-10) and all local and national codes are carefully followed.
IMPORTANT: Any safety screen, guard, glass or grills removed for servicing a fireplace/room heater must be replaced
prior to operating the fireplace/room heater.
BLOWER OPERATION
This fireplace is designed so the blower operates continually when the body is of this fireplace is hot and the main burn-
er(s) are on. The blower output can be regulated with the included blower speed control rheostat. NOTE: There will be
a delay before the blower operates during "heat-up" (approx. 10 minutes) and extended blower operation during "cool-
down" of unit (approx. ½ hour).
OPERATION DURING POWER OUTAGES
The fireplace is designed to operate during power outages for 1-1/2 continuous hours, Maximum on HIGH FIRE. The
blower will not operate, but natural convection can be improved by removing the upper grill and opening the screen
doors (depending on the type of optional front installed). After 1-1/2 continuous hours of operation, during the power
This Fireplace must be installed by a qualified service person.