Megger TTR20 Скачать руководство пользователя | Manualshive

Страница: 39 / 60

background image

Maintenance and Troubleshooting

AVTMTTR20 Rev 4 Dec 2015

31

Error Messages

All TTR20 error messages are divided by 3 categories: self-test error messages,
test error messages, and miscellaneous error messages.

The self-test error messages may appear on the opening screen during power-up
self-test procedure. The Table 5-2 below shows the messages.

Table 5-2 Self-test Error Messages

Error Message

Description of error and action required

UNIT INOPERATIVE

One of the power supply voltages is too low,
or A/D converter is not working for the
reference oscillator. Contact the factory for
repair.

REPLACE BATTERY!
UNIT WILL TURN OFF

The remaining battery capacity is less than 5
%. Unit will turn off in 10 sec. Replace all six
batteries. After the batteries are replaced,
continue testing.

The test error messages may appear on the screens during testing of
transformer. The Table 5-3 below shows the messages.

Table 5-3 Test Error Messages

Error Message

Description of error and action required

REPLACE BATTERY!
UNIT WILL TURN OFF

The remaining battery capacity is less than 5 %.
Unit will turn off in 10 sec. Replace all six
batteries. After the batteries are replaced,
continue testing.

EXC.CURRENT TOO
HIGH

Excitation current is higher than 100 mA. Check
for any wrong test cable connections or
transformer winding shorts.

CHECK CONNECTIONS

The test leads are not properly connected to
transformer. Connect the leads properly.

Test lead(s) is open. Contact the factory for
repair.

Transformer winding(s) is open. Fix the problem
before continuing the test.

«
...
37
38
39
40
41
...
»

Содержание TTR20





























































Отзывы:

Нет отзывов

Похожие инструкции для TTR20

Бренд: York Fitness Страницы: 34

Бренд: Cadman Страницы: 66

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: Kärcher Страницы: 88

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: XTA Страницы: 20

Бренд: Kawai Страницы: 166

Бренд: Land Pride Страницы: 32

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: Quadro mdb Страницы: 11

Бренд: Yamaha Страницы: 178

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды