Megger TTR20 Скачать руководство пользователя | Manualshive

Страница: 30 / 60

background image

M

AVTMTTR20 Rev 4 Dec 2015

22

Test in Progress Screen

Figure 4-13 shows the TEST IN PROGRESS screen.

Figure 4-13 Test in Progress Screen

If during testing an abnormal condition is detected, one of the error messages
listed in the ERROR MESSAGES section is displayed on the screen.
In case of emergency, press the red button on keypad. It will turn TTR20 OFF.
After emergency situation is gone, turn power ON (green button) to start TTR20
operation.

Test Result Screen

At the completion of the test, the TEST RESULTS screen (Figure 4-14) appears.

Figure 4-14 TTR20 Test Result Screen

The TEST RESULTS screen displays the test voltage used for the test, the
measured turns ratio, the tested winding polarity (“+” for in phase or normal
polarity, and ”-“ for out of phase or reversed polarity), and the tested winding
excitation current.

From this screen, the test results may be printed out on the optional printer
connected to RS232/PRINTER port of the TTR20.

To repeat the test or to start a new one, press the

◊

button on a keypad.

TEST RESULTS

TEST VOLTAGE: 1.5 V
TURNS RATIO: +12.735
EXC. CURRENT: 34 µA

PRINT:“



“ DATA

▼

HEADER

“

◊

“ FOR NEW TEST

TEST IN PROGRESS…

PRESS RED BUTTON FOR
EMERGENCY SHUTDOWN

«
...
28
29
30
31
32
...
»

Содержание TTR20





























































Отзывы:

Нет отзывов

Похожие инструкции для TTR20

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: GE Страницы: 212

Бренд: Laserworld Страницы: 8

Бренд: Laserworld Страницы: 6

Бренд: LaserLiner Страницы: 56

Бренд: LaserLiner Страницы: 54

Бренд: Yamaha Страницы: 16

Бренд: YASKAWA Страницы: 81

Бренд: YASKAWA Страницы: 52

Бренд: Makita Страницы: 208

NTP TECHNOLOGY DAD Thunder Core 256

Бренд: DAN Страницы: 16

DependaBar DB-18-PCW

Бренд: Healthcraft Страницы: 13

Бренд: Frick Страницы: 36

Ribiland PR4EN1ELEC

Бренд: Ribimex Страницы: 68

Бренд: LABORIE Страницы: 116

Бренд: Fisher Scientific Страницы: 44

Haymakers Hooimakers F80-350V

Бренд: Falcon Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды