Megger TTR20 Скачать руководство пользователя | Manualshive

Страница: 16 / 60

background image

M

AVTMTTR20 Rev 4 Dec 2015

8



Safety is the responsibility of the user.



Follow your company safety procedures.



Misuse of this equipment can be extremely dangerous.



The purpose of this equipment is limited to use as described in this manual. Do
not use the equipment or its accessories with any device other than specifically
described.



Never connect the test set to energized equipment.



Do not use the test set in an explosive atmosphere.



Corrective maintenance must only be performed by qualified personnel who are
familiar with the construction and operation of the test set and the hazards
involved.



Refer to IEEE 510 - 1983, IEEE Recommended Practices for Safety in High-
Voltage and High-Power Testing, for additional information.

If the test equipment is operated properly and all grounds correctly made, test
personnel need not wear rubber gloves. As a routine safety procedure, however,
some users require that rubber gloves be worn, not only when making
connections to the high-voltage terminals, but also when manipulating the
controls. Megger considers this an excellent safety practice.

Users of equipment should note that high-voltage discharges and other sources
of strong electric or magnetic field may interfere with the proper functioning of
heart pacemakers. Persons with heart pacemakers should obtain expert advice
on the possible risks before operating this equipment or being close to the
equipment during operation.

Cautions and Warnings

Warning and caution notices are used throughout this manual where applicable
and should be strictly observed.

«
...
14
15
16
17
18
...
»

Содержание TTR20





























































Отзывы:

Нет отзывов

Похожие инструкции для TTR20

Бренд: Landoll Страницы: 83

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: jcb Страницы: 41

Бренд: Jasco Страницы: 2

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

Бренд: Pari Страницы: 282

Бренд: VDO Страницы: 15

Бренд: VDO Страницы: 20

Бренд: Gardco Страницы: 17

Бренд: H&S Страницы: 42

Бренд: Aeroflex Страницы: 211

Бренд: GE Страницы: 18

Бренд: Öhlins Страницы: 8

Бренд: ?HC Страницы: 2

Бренд: SAC Страницы: 2

Бренд: Garrick Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды