Megger TTR20 Скачать руководство пользователя | Manualshive

Страница: 31 / 60

background image

Setup, Connections & Operation

AVTMTTR20 Rev 4 Dec 2015

23

Use with the Optional Printer

If you are using the optional printer, plug the printer cable supplied into the
RS232/PRINTER receptacle on the TTR20 test set and turn it on. A separate
manual is supplied with the printer. Refer to it for specific information about how
to connect, operate, and care for the printer.

NOTE: TTR20 should be turned on before turning on printer. If

the printer is attached and turned on first, a blank screen
will appear. In this case turn off the TTR and the printer.
Then power on the TTR20 first.

Pressing



after the first test result will provide a header and the data on the

print out. Each subsequent press of enter will print results (data) only. If a new
header is needed, pressing the



key will print a new header. Then the enter

key will need to be pressed to print the data that is presently on the screen.
Printing headers and data may be repeated as many times as needed.

Header information and test results may be printed from the test results screen

MEGGER

TTR20 TRANSFORMER TURN RATIO TESTER

CATALOG NO. TTR20

TRANSFORMER ID:

TTR S/N:

COMMENTS:

TEST RESULTS

TEST VOLTAGE: 8.0 V
TURNS RATIO:+69.966
EXC.CURRENT: 96.4µA

TEST RESULTS

TEST VOLTAGE: 8.0 V
TURNS RATIO:+79.966
EXC.CURRENT: 94.4µA

Figure 4-15 Sample Test Report

«
...
29
30
31
32
33
...
»

Содержание TTR20





























































Отзывы:

Нет отзывов

Похожие инструкции для TTR20

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: ParaBody Страницы: 4

Бренд: ADVANCED HOME CARE Страницы: 16

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: Hagie Страницы: 141

Бренд: iFIT Страницы: 11

Бренд: Nederman Страницы: 89

Бренд: Nederman Страницы: 71

Бренд: Nederman Страницы: 131

Бренд: X-Cite Страницы: 2

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: Rational Страницы: 60

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды