Megger TTR20 Скачать руководство пользователя | Manualshive

Страница: 24 / 60

background image

M

AVTMTTR20 Rev 4 Dec 2015

16

Three-Phase, Two-Winding Transformers

Perform the following setup procedure for three-phase, two-winding transformers:

1. Connect the test cables to the test set.
2. Connect the clips marked H1 and H2 of the test lead to the phase being tested

(high-voltage winding) terminals of the transformer under test.

3. Connect the clips marked X1 and X2 of the test lead to the phase being tested

(low-voltage winding) terminals of the transformer under test.

F

WARNING

Never interchange connections between the high- and
low-voltage transformer terminals. Failure to observe
proper connections will result in a safety hazard and
may result in damage to the test set or transformer.

The unused H0 and X0 terminals of the transformer should be kept clear of
ground and personnel because they could become energized during the test.

With wye connected windings, a neutral connection is normally available.

Three-Phase, Three-Winding Transformers

This type of transformers has primary, secondary and tertiary windings. Primary
and secondary windings are tested as a regular three-phase, two-winding
transformer. To test tertiary winding, perform the following setup procedure:

1. Connect the test cables to the test set.
2. Connect the clips marked H1 and H2 of the test lead to the phase being tested

(high-voltage winding) terminals of the transformer under test.

3. Connect the clips marked X1 and X2 of the test lead to the corresponding

tertiary phase being tested (low-voltage winding) terminals (Y1 and Y2) of the
transformer under test.

F

WARNING

Never interchange connections between the high- and
low-voltage transformer terminals. Failure to observe
proper connections will result in a safety hazard and
may result in damage to the test set or transformer.

With wye connected windings, a neutral connection is normally available.

Current Transformers (CTs)

Connections to CTs are made backwards compared to power, distribution or
potential transformers. The H terminals on the test lead set must be connected to
the X terminals on the CT; and the X terminals on the test lead set must be
connected to the H terminals on the CT.

«
...
22
23
24
25
26
...
»

Содержание TTR20





























































Отзывы:

Нет отзывов

Похожие инструкции для TTR20

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: Jasco Страницы: 2

Бренд: ubicquia Страницы: 36

Бренд: V-GREAT Страницы: 4

Бренд: GE Страницы: 2

Бренд: Fillauer Страницы: 12

Бренд: Hoshizaki Страницы: 35

Бренд: lumishore Страницы: 13

Бренд: Kalco Lighting Страницы: 6

Wensco AnPro180 Stick

Бренд: G2G Lighting Страницы: 3

Бренд: GreenDS Страницы: 24

Бренд: Ryobi Страницы: 168

LFC500-FS Series

Бренд: Watts Страницы: 8

Bowflex SelectTech Stand

Бренд: Nautilus Страницы: 8

Бренд: Megger Страницы: 24

Бренд: Vari Lite Страницы: 6

Бренд: OCEM Страницы: 37

Бренд: Aqua Creek Products Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды