Megger TTR20 Скачать руководство пользователя | Manualshive

Страница: 35 / 60

background image

AVTMTTR20 Rev 4 Dec 2015

27

5

MAINTENANCE AND TROUBLESHOOTING

Maintenance

Maintenance should be performed only by qualified persons familiar with the
hazards involved with high-voltage test equipment. Read and understand Section
2, Safety, before performing any service.

The TTR20 test set is sturdily constructed and requires no periodic maintenance.
Routine maintenance is all that is required for the TTR test sets. Inspect the
cable assemblies occasionally to ensure they are in good condition.

The appearance of the TTR test set can be maintained by occasionally cleaning
the case, panel and cable assemblies. Clean the outside of the carrying case
with detergent and water. Dry with a clean, dry cloth. Clean the control panel with
a cloth dampened with detergent and water. Do not allow water to penetrate
panel holes, because damage to components on the underside may result. An
all-purpose, household spray cleaner can be used to clean the panel. Polish with
a soft, dry cloth, taking care not to scratch the display screen cover. Clean the
cables and mating panel receptacles with isopropyl or denatured alcohol applied
with a clean cloth.

Calibration Check

A complete performance and calibration check should be made at least once
every year. This will ensure that the TTR20 test set is functioning and calibrated
properly over the entire measurement range. The TTR20 calibration is performed
on each new or repaired unit before sending it to a customer. There is a special
TTR20 final calibration procedure which requires a NIST-traceable test
equipment to be used. As a result of such calibration procedure, each TTR20
may be NIST certified.

To check the TTR20 calibration at a customer site or in the field, the Megger
Calibration Standard Cat. No. 550055 or equivalent standard should be used. To
perform a quick simplified calibration check, the Megger Calibration Standard
Cat. No. 550555 may be used. The last standard has eleven switchable turn ratio
settings which cover the turns ratio range from 0.8:1 to 2000:1(5-digit resolution).
Using these Calibration Standards will confirm proper calibration of TTR20.

«
...
33
34
35
36
37
...
»

Содержание TTR20





























































Отзывы:

Нет отзывов

Похожие инструкции для TTR20

Бренд: Labnet Страницы: 5

Бренд: Ecco Страницы: 3

Бренд: NEC Страницы: 54

Бренд: Samson Страницы: 2

Бренд: Tar River Страницы: 26

Бренд: ZOLL Страницы: 38

Бренд: ZOLL Страницы: 36

Nature2 Fusion soft

Бренд: Zodiac Pool Systems Страницы: 52

Бренд: Oliver Страницы: 38

Бренд: G21 Страницы: 7

Бренд: Dräger Medical Страницы: 92

Бренд: Gfp Страницы: 14

Бренд: SUHNER MACHINING Страницы: 30

CB Ohio Special 100 HP

Бренд: CleaverBrooks Страницы: 200

Бренд: XFT Medical Страницы: 44

Бренд: Exo Terra Страницы: 11

SKINGUARD Series

Бренд: KAP Medical Страницы: 39

Бренд: IntesisBox Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды