manualshive.com logo in svg

Megger TM1700 Series, Руководство пользователя

Поделиться
Скачать
Megger TM1700 Series Скачать руководство пользователя страница 26

26

TM1700-sEriEs

ZP-BL16E

BL1448GE

4 CABA LOCAL 

4 

C

ABA Local 

CABA Local is the standard software program to oper-
ate instruments with built-in screen . in CABA Local 
you run the tests, view the measurements, do set-ups 
etc.

4.1 Start/Shut down CABA 
Local

Start

1] 

Connect the instrument to the mains. Always 
use the power cord supplied with the unit.

2] 

Switch on the instrument by pressing the ON/
OFF button on the control panel.

3] 

During the start-up procedure the ON/OFF 
indication lamp will blink until Windows® XP 
starts. Then all indication lamps on the con-
trol panel will lighten up, the OPERATE and 
OPERATE/MEASURE lamps blinking.

Note

  During the start-up procedure do not try to 

operate the instrument. If you try to do a 
measurement during the start-up you will risk 
loosing the recorded data.

4] 

When the screen below is shown the instru-
ment is ready to run. The Analyzer View is 
the start screen that  visualizes the link be-
tween instrument and the test object. 

Shut down

1] 

 Press the ON/OFF button.

Содержание TM1700 Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды