manualshive.com logo in svg

Megger TM1700 Series, Руководство пользователя

Поделиться
Скачать
Megger TM1700 Series Скачать руководство пользователя страница 17

BL1448GE

ZP-BL16E

TM1700-sEriEs

17

3 sysTEM OVErViEW 

TM1760

The TM1760 is equipped as a TM1750 plus three 
analog channels.

TM1760 with 3 extra analogue 
channels

The TM1760 with three extra analog channels (totally 
6 analog channels).

3.2 Control panel

❷

❶

❸

❹

❶

POSITION

indicates the position of the circuit breaker main 
contacts if the coil circuit is connected to the Control 
section and “Auto detect” is enabled. 
“O” indicates Open position 
“i” indicates Closed position

Note 

Position indicates per operating 
mechanism(s). If the Circuit Breaker has 
common operating mechanism only one 
LED will indicate the CB position.

❷

SEQUENCE

indicates the next operation of the circuit breaker. if 
Auto-detect breaker state is enabled in CABA Local 
or CABA Win, only possible sequences for the circuit 
breaker are selectable.

❸

ON/OFF

Power on/off switch

❹

OPERATE/MEASURE

initiates the selected operation sequence and makes 
the measurement. Green “rEADy” LED must be lit 
before turning the rotary switch. The yellow “OP-
ErATiNG” LED is blinking as long as the sequence is 
performed.

Содержание TM1700 Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды