Megger TM1700 Series Скачать руководство пользователя страница 10

Страница: 10 / 92

Figure 1.3-1

TM1700-sEriEs

ZP-BL16E

BL1448GE

1 sAFETy

1.3 Protective earthing
procedure in HV
environments

IMPORTANT

Protective earth (ground)

Connect the clamp of the yellow/green protective
conductor supplied with

instrument

to station earth

(ground) and the other end of the conductor to the
terminal on

instrument

marked

This connection must be done before any test cables
and the mains supply cable are connected to

instru-

ment

and this connection shall be the last connection

removed.

The earthing (grounding) is needed since induced cur-
rent from the High-Voltage Circuit Breaker can cause
hazardous voltages. see Figure 1.3-1.

Preparation of the circuit breaker

Before connecting or disconnecting the

instrument

to a High-Voltage Circuit Breaker, make sure the
breaker is closed and earthed (grounded) on both
sides according to local safety regulations.

Connection of test cables to the circuit
breaker

All connections and disconnections of cables at the
Circuit Breaker shall be done while the breaker is
closed and grounded on both sides according to local
safety regulations.

Mains supply - Voltage

The

instrument

shall only be supplied by power ac-

cording to the specifications stated at the mains inlet
on

instrument

Always connect the

instrument

to a power outlet

with protective ground.

Mains supply - Protective earth (ground)

Dangerous voltage may be present in systems that are
earthed separately.

Содержание TM1700 Series





























































































Результаты поиска

Содержание TM1700 Series

Отзывы:

Бренды по названию

Популярные бренды

Megger TM1700 Series, Руководство пользователя

Результаты поиска

Содержание TM1700 Series

Отзывы:

Бренды по названию

Популярные бренды