REMOTE START OPERATION:
A. TO REMOTE START THE VEHICLE:
1. Press
button twice on the transmitter.
2. The parking light will activate to indicate the remote start received the signal.
3. The engine will start approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking light will turn on again and climate controls will
activate and adjust the vehicles interior temperature to your preset setting.
5. The vehicle will run for 5 to 30 minute cycle and automatically shut down.
Note:
The Remote Start Unit will not start the vehicle if any one of the following
conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to OFF position. (If installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”
SAFE START (Child safety mode)
(See Start Feature
I – 5
Programming)
Factory defaults setting to press the
button twice on the transmitter to start the vehicle. Programming this
feature to eliminate an accidental remote start, when kids enter this transmitter, it enquires:
The user presses the transmitter
and
buttons at the same time to start the vehicle.
B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START:
To operate the vehicle while engine running on the remote start:
1. Insert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note:
If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
C. TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been removed from the ignition. This
feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would
like to leave the motor running and the climate control on.
1. Before turning off the engine, press the
button twice on the transmitter and the LED indicator will flash
3 times to confirm enter.
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time elapsed or shutdown input is received.
E. TURBO TIMER MODE:
(See Start Feature
“I - 6”
Programming)
Turbo timer mode keeps the engine running after arriving at you destination for a programmable period of 1/
3 or 5 minutes, This allows the system’s time to conveniently cool down the turbo after you have left the
vehicle. To activate:
1. While engine is running, place the transmission gear in the park position and pull up the hand brake.
2. Before turning off the engine, press and release
and
buttons at the same time.
-- The parking light wills turn on to indicate the remote start has entered turbo charge mode. --
3. Pull off the “Ignition Key” from the key cylinder.
-- Engine keeps running. --
4. Exit and secure the vehicle.
--
Engine continues running until the pre-programmed time elapsed.
--
F. TIMER START:
(See Start Feature
“I - 7”
Programming)
This unit can be programmed to start and run the engine every 3 (2) hours. The engine will run for the
programmed running time and then shut down.
IMPORTANT
: Timer Start should be used only in open areas, never start and run the vehicle in on enclosed
space as a garage or carport.
This feature is design for an extreme cold climate usage. The system will auto start the vehicle every 3 (2)
hours, to prevent engine freezing and hard to start.
A MAXIMUM OF SIX CYCLES CAN OCCUR.
ENTER:
1. Press the
button twice to remote start the vehicle. As soon as the vehicle is running and the parking
light have turned on or flashing.
2. Immediately depress the
button once, within 2 seconds
3. Rapidly depresses the
button. The parking light will flash (3) times. The siren or horn chirps (3) times.
The vehicle is now programmed to start every 3 (2) hours.
4. Press the brake pedal to stop the vehicle running.
Exit the timer start:
Timer start can be exited manually as follows:
Make sure the remote start system is not operating the engine.
23