5
+
Press
-
button = Activate
Remote Start.
Press
+
button = Activate
Remote Start.
Press
button =
Activate Remote
Start.
The Vehicle has
aftermarket Turbo
timer installed:
The system Can be
Arm with the engine
running and the
shock sensor will be
bypass as long as
the engine running.
The Vehicle has
aftermarket Turbo
timer installed:
The system Can be
Arm with the engine
running and the
shock sensor will be
bypass for three
minutes
Built-in Turbo Timer
Control is Active:
Press
and
buttons at the same
time to control
Engine running one
minute.
6
+
The Vehicle without
Turbo (The system
Cannot be Arm with
the engine running)
Five chirps
= Built-in Turbo Timer Control is Active / Press
and
buttons at the same time to control Engine running three
minutes.
Six chirps
= Built-in Turbo Timer Control is Active / Press
and
buttons at the same time to control Engine running five
minutes.
7
+
3 Hour Time start
2 Hour Time Start
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
SAFE START (Child safety mode)
Factory defaults setting to press the
button twice to start the vehicle.
Programming this feature to eliminate an accidental remote start, when kids enter this transmitter, it requires:
The user presses the transmitter
and
buttons at the same time to start the vehicle.
START FEATURE “
II
” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch
10
times and holding in on the
10
th
push until
five
chirps with a long chirp is hearing
then release the valet switch. You are now in the Start feature
‘II’
programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1
Exit the programming mode. (3 long chirp & 3 parking light flashes to confirm this exit.)
2
+
Engine Checking
TACH.
Engine Checking
Voltage
Engine Checking
OFF
RPM
learning
3
Start Timer:
0.6-second
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4 chirps),
1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-second (7 chirps),
2.0-second (8 chirps), 3.0-second (9 chirps), 4.0-second (10
chirps),
4
Low check level
Hi check level
5
-
Start / Stop the system for TESTING & ADJUSTMENT
6
+
Without Shock
sensor Test Mode
With Shock Sensor
Test Mode
Exit
:
Press the
button on the transmitter. A 3 long chirps & 3 parking light flashes to confirm exit.
ENGINE CHECKING TACH. / RPM LEARNING
Important Note:
You must program the “Tach Signal” before trying to remote start.
1. Turn the Ignition switch ‘ON/OFF’
3
TIMES and stay in
OFF
position.
2. Push the Valet switch
10
times and holding in on the
10
th
push until
five
chirps with a long chirp is hearing
then release the valet switch.
3. Press and release the transmitter
and
buttons at the same time once to set the “Engine Checking
TACH.” [1] LED flash, [1] chirp to confirm this setting.
4. Press and release the transmitter
button once, [1] LED flash, [1] chirp to indicate the system in features
“RPM Learning mode”.
5. Start the vehicle with the key. (While the engine is running, the parking light & LED will flash, If don’t,
please check tachometer White/Red wire connection.
(H7/8)
14
