McQuay IM 689-2 Скачать руководство пользователя | Manualshive

Страница: 42 / 52

background image

42

IM 689-2

MicroTech Controller Configure Tool

The basic information collected by the MicroTech Controller Configure tool can be used to
troubleshoot communications problems that may occur with specific MicroTech controllers. For
example, if all but one unit ventilator is communicating on the network, you could use this tool to
check the non-communicating controller’s port configuration (e.g., it might be set up as level 3
instead of level 2). See Figure 26.

Figure 26. MicroTech Controller Configure Tool, Information Screen

Following are brief descriptions of each information field:

MicroTech Address

The actual MicroTech network address that the controller is using. For a
level-2 controller, the first part of the address should match the hex
switch setting. For a level-3 controller, the last part of the address should
match the hex switch setting. If this is not the case, check the controller
level and/or try cycling power to the controller.

Controller Series

The style of the MicroTech controller. Different style controllers have
different memory maps.

Program IDENT

The program identification code for the actual MicroTech program that is
loaded in the controller.

Communication
Port Speeds

The configured data transmission speeds for the two communications
ports. These configured speeds can be changed with this tool.

Communication
Port Configuration

The port configurations of the two communications ports. The controller
level is part of the port configuration. The port configuration can be
changed with this tool. The most common level-2 configuration is shown
in Figure 26.

Checksums

The checksums for the controller. The checksums must match; otherwise,
the controller’s program will not run. When you change port speeds or
configurations, the Setup Wizard will automatically adjust the Actual
checksum to match the EOS Calculated checksum.

Click the Configure button to change the MicroTech controller’s port configuration or port speeds, or
click the Main Screen button to return to the Main screen. Clicking the Refresh Screen button will
cause the information to update.

If you click the Configure button, the Setup Wizard will warn you that the tool cannot be used on
certain types of MicroTech controllers. Those controllers have special programming and changes to
their port configurations can be made only from their keypad/displays. If the controller you are
connected to is not one of those listed, proceed to the edit screen. See Figure 27. If the checksums do
not match, the tool will not allow you to proceed to the edit screen. In this instance, MicroTech
Monitor software should be used instead.

«
...
40
41
42
43
44
...
»

Содержание IM 689-2





















































Отзывы:

Нет отзывов

Похожие инструкции для IM 689-2

Бренд: Luminext Страницы: 8

Бренд: Digi Страницы: 6

EliteConnect SMCWHSG14-G

Бренд: SMC Networks Страницы: 2

Бренд: New Rock Technologies Страницы: 75

NetPerformer SDM-9220 Series

Бренд: Memotec Страницы: 146

SmartNode 5540E Series

Бренд: Patton Страницы: 77

Бренд: Zennio Страницы: 35

HD67F18-B2 Series

Бренд: ADF Web Страницы: 33

Бренд: Zte Страницы: 14

MiniHub Pro WLRRTES-102 TBMH110

Бренд: Browan Страницы: 14

Бренд: TelcoBridges Страницы: 80

Бренд: 3Com Страницы: 306

Бренд: C2G Страницы: 39

Бренд: RadiSys Страницы: 198

Бренд: Avaya Страницы: 116

Бренд: Orchid Telecom Страницы: 3

NI 9795 WSN C Series

Бренд: National Instruments Страницы: 17

Бренд: XPEECH Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды