McQuay IM 689-2 Скачать руководство пользователя | Manualshive

Страница: 30 / 52

background image

30

IM 689-2

Installing the BACdrop Setup Wizard

The installation program creates folders as needed, copies files from the install diskettes to your hard
disk, and creates a BACdrop Setup Wizard program group under the Start menu’s Programs menu.

To install the BACdrop Setup Wizard

1. Insert the BACdrop Setup Wizard Disk 1 into the floppy drive on your PC.
2. Click the Start button on the taskbar and then click Run.

The Run dialog box appears.

3. Type “a:setup” and click OK.
4. Follow the directions in the Install program.

Electronic Documentation

The Install program allows you to install electronic versions of most BACdrop documents including
BDIPs, PICS, and this manual. You can choose from four installation options: Typical, Minimum,
Complete, and Custom. The Custom option allows you to select individual documents for
installation; for example, BD 06-7,

MicroTech Series-200 Centrifugal Chiller Controller

.

All electronic documentation is in PDF format, which requires Adobe Acrobat Reader 4.0 to view or
print. Adobe Acrobat Reader 4.0 is a free program that can be downloaded from the Adobe Web site,
http://www.adobe.com.

Starting the BACdrop Setup Wizard

You can run the BACdrop Setup Wizard at any time. The PC does not need to be connected to a
BACdrop gateway when you start the program.

To start the BACdrop Setup Wizard

1. On the Start menu, point to Programs, BACdrop Setup Wizard, and then choose the BACdrop

Setup Wizard program.

2. Type the password in the box.

The password is “BACdrop!” (case sensitive).

3. Click OK or press Enter.

The Main screen appears.

Figure 11. BACdrop Setup Wizard, Main Screen

«
...
28
29
30
31
32
...
»

Содержание IM 689-2





















































Отзывы:

Нет отзывов

Похожие инструкции для IM 689-2

Бренд: SpectraLink Страницы: 2

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 8

VersiComm VC1COMMA

Бренд: Siemens Страницы: 22

SIRIUS 3RK3141 Series

Бренд: Siemens Страницы: 19

SIMATIC RTLS4330G

Бренд: Siemens Страницы: 28

Бренд: Siemens Страницы: 48

Sinamics Connect Series

Бренд: Siemens Страницы: 101

Бренд: Siemens Страницы: 124

Бренд: Siemens Страницы: 866

Бренд: Seneca Страницы: 2

Бренд: Electro Industries/GaugeTech Страницы: 118

Бренд: Lauda Страницы: 24

Бренд: 3Com Страницы: 58

Бренд: 2N Telekomunikace Страницы: 5

Бренд: RCA Страницы: 76

FPC-N34: FPC-N35

Бренд: FieldServer Страницы: 28

NeoGate TG Series

Бренд: Yeastar Technology Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды