manualshive.com logo in svg

McHale Twiner, Инструкция оператора

Поделиться
Скачать
McHale Twiner Скачать руководство пользователя страница 40

McHale

 Twiner

40

Track position

This is shown if you switch to AUTO mode and the track is 
not in the home position. Twine cannot begin to feed in 
AUTO mode unless the twine track is in the home position. 
Press the twine cut button (soft-key 2) to reset the track to 
the home position.

(2102)

Single twine feed error

This is shown during an automatic twine cycle if there is no 
twine seen from one of the twine feed sensors. The twine 
cycle will continue with one twine. The operator has the 
option to press the twine cut button (soft-key 2) to cut the 
one remaining twine. When the twine has cut and the track 
is back in the home position they can press the re-twine 
button.

(2103)

Double twine feed error

This is shown during an automatic twine cycle if there is no 
twine seen from both of the twine feed sensors.The track 
automatically returns to the home position when this 
warning is shown.

(2104)

CAN bus warning

This is shown if CAN bus communication is lost with the 
twiner module. No twine functions will operate when this 
warning is shown.

(2105)

Содержание Twiner











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды