manualshive.com logo in svg

McHale Twiner, Инструкция оператора

Поделиться
Скачать
McHale Twiner Скачать руководство пользователя страница 31

McHale

 Twiner

31

Core density

The core density can be set from 0 - 10. This sets the 
density for the core diameter setting, then the bale density 
setting is used for the remainder of the bale formation.

Bale density

The density can be set from 0 - 10. Normally a maximum 
of 8 is adequate to produce good dense bales. A higher 
setting may be required in wet crop conditions. .

Revolutions of twine at the edge

This sets the number of revolutions of twine around the 
edge of the bale. It is adjustable from 1 - 10. The default is 
set to 4.

Distance from the edge

This sets the distance from the edge of the bale. It is 
adjustable between 8 - 22 cm. The default is set to 8.

No. of stops between the edge and centre

This sets the number of stops between the edge and 
centre of the bale. It is adjustable from 1 - 10. The default 
is set to 3.

Time delay at each stop

This sets the time for each stop. It is adjustable from 
0.1 - 30 s. The default is set to 1.0 s.

Revolutions of twine at the centre

This sets the number of revolutions of twine around the 
centre of the bale. It is adjustable from 1 - 10. The default 
is set to 4.

Содержание Twiner











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды