manualshive.com logo in svg

McHale Twiner, Инструкция оператора

Поделиться
Скачать
McHale Twiner Скачать руководство пользователя страница 39

McHale

 Twiner

39

6.5  Warning messages 

Chamber open

This screen is displayed when either the left or right door 
latch sensor is detected open.

AUTO mode cannot be selected when the chamber is open.

If the chamber opens inadvertently during an automatic 
cycle, a warning beeper will sound to alert the operator.

Drop floor sensor

As soon as the drop floor moves away from the working 
position, this warning will be displayed to alert the operator. 
The red light beside button 7 will also flash.

(2002)

Knife pressure too high (V6750 only)

This is displayed when the knife pressure is too high for 
baling (above 65 bar hydraulic pressure).

It is normal for this warning to be displayed during knife 
activation with maximum tractor pressure. It must be 
lowered again before baling. 

(See ‘Knife operation (V6750 

only)’)

(2003)

Bale not ejected

This screen is always shown as soon as the chamber is 
opened after binding. As the bale ejects from the chamber 
and rolls off the kicker, a beep will sound and the bale image 
will disappear to indicate that the chamber door can be 
closed.

Track motor

This is shown if there is a track motor fault. This will also be 
displayed if the track has gone too far towards the edge or 
the centre of the bale.

(2101)

Содержание Twiner











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды