manualshive.com logo in svg

Mazda 6 Facelift 2005, Руководство по обучению, Страница: 60 / 274

Поделиться
Скачать
Mazda 6 Facelift 2005 Скачать руководство пользователя страница 60

Diesel Engines 

Engine 

Injectors  

• 

Solenoid valve-type injectors with lower power consumption and better response have 
been introduced.  

 

 

M6FL_01068 

 

1 

From common rail 

3 

To fuel tank 

2 Connector 

  

 
 

NOTE:

  Since the size of the injector connector is relatively big compared to the diameter of 

the injector head, there might be an interference between the connector and the 
injector seal during removal and installation of the cylinder head cover. In order to 
prevent any damage to the seal, wrap vinyl tape around the injector connector 
covering the connector edges. 

 

• 

In addition, the leak-off lines of the injectors are located under the cylinder head cover. 
As a result, the total leak-off amount of the injectors must be measured and compared to 
the values of a known good vehicle in order to detect a leaking solenoid valve.  

 

NOTE:

  Always replace the gaskets of the injector leak-off lines when removing them. As the 

leak-off lines are located under the cylinder head cover, fuel leaking from the lines 
can contaminate the engine oil. This results in engine oil dilution and hence in engine 
damage.  

 

01-46 

Service Training Mazda6 Facelift 

Содержание 6 Facelift 2005



















































































































































































































































































Отзывы:

Нет отзывов