Mazda 6 Facelift 2005 Скачать руководство пользователя страница 265 | Manualshive

Страница: 265 / 274

background image

Body & Accessories

Accessories

Rear Seat Belt Warning Alarm

•

The rear seat belt warning LEDs are installed on the installation area of the rear view
mirror.

•

The indicator and the buzzer are built-in corresponding to the seat belt for each rear
seat.

Operation

•

After the ignition switch is turned to the ON position, each indicator illuminates
continuously while the generator warning light is illuminating:

–

green when the seat belt is fastened (buckle switch is on)

–

red when the seat belt is not fastened (buckle switch is off)

•

Each indicator turns off if the condition corresponds to any of the following:

–

When the ignition switch is in the LOCK position.

–

When approx. 40 s have elapsed since the generator warning light turned off (engine
runs).

•

If the buckle switch signal changes (on to off, or off to on) with the ignition switch in the
ON position and the indicator is not illuminated, the corresponding seat belt indicator
illuminates.

•

In addition, when the buckle switch is changed from off to on (seat belt was unfastened),
the buzzer inside the rear seat belt reminder indicator sounds for approx. 0.5 sec to alert
the driver.

Service Training Mazda6 Facelift

09-83

«
...
263
264
265
266
267
...
»

Содержание 6 Facelift 2005



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6 Facelift 2005

Бренд: Ranger design Страницы: 6

Бренд: Camcar Страницы: 6

Бренд: Acdeos Страницы: 7

Бренд: Kargo Master Страницы: 5

Бренд: Q'STRAINT Страницы: 10

Бренд: Yakima Страницы: 8

Бренд: Honda Страницы: 73

Бренд: GATmatic Страницы: 13

Бренд: TATA Motors Страницы: 156

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Magneti Marelli Страницы: 2

Бренд: RAM Страницы: 76

Бренд: Advantech Страницы: 59

Бренд: Audiovox Страницы: 24

Бренд: Mercedes-Benz Страницы: 2

Бренд: Westin Страницы: 2

Бренд: VER-MAC Страницы: 64

Vehicle Asset Communicator

Бренд: I.D. Systems Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды