Mazda 6 Facelift 2005 Скачать руководство пользователя страница 199

Страница: 199 / 274

Body & Accessories

Accessories

Seat Position Memory

•

Three seat positions can be programmed in the position memory control module
corresponding to the memory switch.

•

An additional seat position can be programmed corresponding to each transmitter.

•

Programming of the seat position is possible according to the following procedures.

Seat Position Programming Using the Memory Switches

1. Slide the seat manually to the desired position.

2. Press and hold the set switch. Then press one of the memory switches 1, 2, or 3.

3. Buzzer sounds and the seat position is programmed.

Seat Position Programming Using the Transmitter

1. Slide the seat manually to the desired position.

2. Press and hold the set switch. Then press the UNLOCK button on the transmitter.

3. Buzzer sounds and seat position is programmed.

NOTE

: If the vehicle battery is disconnected for more than 5s, all of the seat position

memory will be erased.

Seat Positioning Using Memory Switch

•

If all of the following conditions are met, the seat position is automatically called up by
the memory switch operation.

–

Door is open (door switch on).

–

Seat position has been programmed.

–

Ignition switch is in the LOCK position.

–

Vehicle is stopped (vehicle speed 2 km/h [1.24 mph] or less).

Seat Positioning Using Transmitter

•

When the door is opened within approx. 2 s after it is unlocked using the transmitter, the
auto call up operation slides the seat to the programmed position.

Service Training Mazda6 Facelift

09-17

Содержание 6 Facelift 2005



















































































































































































































































































Результаты поиска

Содержание 6 Facelift 2005

Отзывы:

Похожие инструкции для 6 Facelift 2005

Бренды по названию

Популярные бренды

Mazda 6 Facelift 2005, Руководство по обучению

Результаты поиска

Содержание 6 Facelift 2005

Отзывы:

Похожие инструкции для 6 Facelift 2005

Бренды по названию

Популярные бренды