Mazda 6 Facelift 2005 Скачать руководство пользователя страница 215 | Manualshive

Страница: 215 / 274

background image

Body & Accessories

Accessories

Programming New Card Keys

NOTE:

Do not program card keys while WDS or any other computer devices are in the
vehicle. Make sure all card keys are operational and have good batteries.

NOTE:

Auxiliary keys have to be programmed separately as ignition keys.

With Two or More Card Keys

•

If two or more registered card keys are available, additional keys can be programmed
without the use of WDS. A maximum of six card keys can be programmed.

1. Bring the two registered card keys (key 1 and key 2), and the card keys to be

programmed into the vehicle and close all doors.

2. Insert auxiliary key in ignition lock.

NOTE:

The procedure below must be completed up to step six within 30 seconds of

inserting the auxiliary key in the ignition lock.

3. Turn the ignition ON.

4. Push the UNLOCK button on card key 1 once.

5. Push the UNLOCK button on card key 2 once.

6. Turn ignition switch to ACC then back to ON three times.

7. Open and close the driver’s door three times. The door lock actuators will lock once,

then unlock to confirm that key programming mode is active.

8. Push the UNLOCK button on the card key to be programmed twice. The door lock

actuators will lock once, then unlock to confirm that programming was successful.

9. To program additional card keys, remove the auxiliary key from the ignition lock and

repeat the above process again from the start.

With WDS

1. Establish communication between WDS and the vehicle.

2. Select the option

Toolbox

→

Body

→

Security

→

PATS Functions

.

3. Carry out the security access procedure (read out the WDS outcode, and input the

corresponding incode).

4. Select the option Card Key Programming. The door lock actuators will lock once, then

unlock to confirm that key programming mode is active.

5. Push the UNLOCK button on the card key to be programmed twice. The door lock

actuators will lock once, then unlock to confirm that programming was successful.

6. To program additional card keys, remove the auxiliary key from the ignition and repeat

the above process again from step 4.

Service Training Mazda6 Facelift

09-33

«
...
213
214
215
216
217
...
»

Содержание 6 Facelift 2005



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6 Facelift 2005

Бренд: JAC Страницы: 70

Бренд: Acdeos Страницы: 38

Бренд: Yakima Страницы: 8

Electronic Parking Disc 3

Бренд: Jacob Jensen Страницы: 2

Бренд: Yakima Страницы: 12

Бренд: Nuna Страницы: 17

Бренд: tams elektronik Страницы: 44

BASIC TLL171231

Бренд: Tellur Страницы: 5

Бренд: GAC MOTOR Страницы: 356

Бренд: Camecho Страницы: 2

E60-82-007-02-10

Бренд: Eibach Страницы: 3

Бренд: Prorack Страницы: 10

Grand Cherokee SRT 2019

Бренд: Jeep Страницы: 656

Бренд: ULTIMATE SPEED Страницы: 56

CMPC-22 Fujitsu-Siemens PocketLoox 410

Бренд: Carcomm Страницы: 2

Бренд: Kuda Страницы: 3

Бренд: TOP VEHICLE TECH Страницы: 8

C-Max Energi 2014

Бренд: Ford Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды