Mazda 6 Facelift 2005 Скачать руководство пользователя страница 208 | Manualshive

Страница: 208 / 274

background image

Accessories Body

&

Accessories

Auto Re-lock Function

•

The doors will automatically re-lock 30 seconds after being unlocked unless any of the
following conditions are met:

–

Any of the doors or liftgate are opened.

–

The auxiliary key is inserted in the ignition.

–

The start knob is pressed.

–

Any of the buttons of the transmitter are operated (the auto re-lock timer will be reset
to ‘0’ if the UNLOCK button is pressed).

–

Any of the request switches are pushed.

Out of Range Auto Lock Function

•

If the card key moves out of the reception range of the antennas while all the doors are
closed, the doors will automatically be locked (this function is set to OFF for new
vehicles).

•

The keyless buzzer sounds one time and the system enters ‘standby mode’ (but locks
are not operated) when the following conditions are met:

–

All doors and liftgate are closed (door switch OFF) after one or more having been
opened (door switch ON).

–

The card key is not inside the vehicle.

–

The card key is within the reception range of the antennas (card key is outside the
vehicle).

–

Auxiliary key is not in the ignition.

–

Start knob is in the LOCK position, and also not being pressed.

•

Approximately two seconds after the keyless antenna determines that no card keys are
within range; the doors are locked.

•

The hazard lights flash once to indicate the doors are locked.

09-26 Service

Training

Mazda6

Facelift

«
...
206
207
208
209
210
...
»

Содержание 6 Facelift 2005



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6 Facelift 2005

Бренд: Mobile Create Страницы: 15

Бренд: Audi Страницы: 12

Бренд: StowAway 2 Страницы: 2

Бренд: UAZ Страницы: 112

Бренд: Scion Страницы: 24

Бренд: A-Tach Mounts Страницы: 2

Бренд: EUFAB Страницы: 4

Бренд: TracRac Страницы: 8

Бренд: APS Страницы: 4

Directechs FORD11

Бренд: Directed Страницы: 23

SILVER line 104

Бренд: AutoMaxi Страницы: 4

Бренд: Volkswagen Страницы: 4

GM DELTA 88 1974

Бренд: Oldsmobile Страницы: 88

VISTA-CRUISER 1970

Бренд: Oldsmobile Страницы: 67

XEV1R22T2 Series

Бренд: hager Страницы: 14

CF-UFORCE-SDK01

Бренд: FALCON RIDGE Страницы: 5

Бренд: LAS Страницы: 4

Бренд: Erde Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды