Mazda 6 Facelift 2005 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 274

background image

Engine Diesel

Engines

Service and Repair

Replacing the Engine Oil

•

Every time the engine oil is replaced, the parameter “Calculated oil dilution” in the PCM
must be reset with the aid of WDS. Therefore, select the option

Toolbox

Æ

Powertrain

Æ

Data Reset

Æ

Engine Oil

.

Manual Regeneration

•

If the DPF is blocked due to an excessive soot amount accumulated, it must be
regenerated manually with the aid of WDS. Therefore, select the option

Toolbox

Æ

Powertrain

Æ

DPF

Æ

DPF Regeneration

.

•

Depending on the amount of soot accumulated in the DPF the PCM automatically
selects normal regeneration mode (34 min) or long regeneration mode (60 min). Long
regeneration mode is performed when the soot amount in the filter exceeds 125 %. Due
to the longer duration the manual regeneration can be performed at a lower exhaust gas
temperature. As a result, damage of the DPF by a violent regeneration following an over-
accumulation of soot is prevented.

•

In order to cancel the manual regeneration process perform the following procedure:

1. Depress the clutch pedal, shift to 1st gear and verify that the engine speed

decreases to idle speed (manual regeneration is cancelled).

2. Shift to Neutral and increase the engine speed to 3000 min

-1

for 1 min (DPF is

cooled).

3. If the manual regeneration must be performed again, wait for approx. 5 min before

re-starting the regeneration process.

NOTE:

Always perform the manual regeneration in a well-ventilated place and use an

appropriate exhaust-gas extraction system. The vehicle should also not be parked in
front of any flammable or low heat resistant material, since high temperature exhaust
gas is emitted during this process. In addition, the hood should be opened to prevent
the engine from overheating. Do NOT apply electrical load (such as turning on the
headlights or rear window defroster) during manual regeneration, since the post
injection amount is changed and regeneration may not be performed correctly.

Service Training Mazda6 Facelift

01-93

«
...
105
106
107
108
109
...
»

Содержание 6 Facelift 2005



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6 Facelift 2005

Бренд: Accel Страницы: 2

Бренд: Camcar Страницы: 6

Бренд: Feniex Страницы: 6

Бренд: Suzuki Страницы: 353

Бренд: Torklift Страницы: 16

AAB-P-RZR900-K2-001

Бренд: SuperATV Страницы: 3

Бренд: ECS Electronics Страницы: 16

Бренд: Saturn Страницы: 440

OPTIA hybrid 2020

Бренд: Kia Страницы: 54

Бренд: FORM FIT Страницы: 2

Бренд: Whelen Engineering Company Страницы: 4

Heavy Duty ProClip

Бренд: Brodit Страницы: 2

Бренд: Toyota Страницы: 204

Бренд: T-Tech Страницы: 1

Бренд: AA Products Страницы: 6

IONIQ HYBRID 2019

Бренд: Hyundai Страницы: 16

Бренд: Ratio Electric Страницы: 16

CITY GO PD349056A

Бренд: Baby Jogger Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды