Mazda 0000-8E-R10 Скачать руководство пользователя страница 9

Страница: 9 / 10

Page 9 of 10

INSTALLATION INSPECTION

TRAILER HITCH WIRING KIT

Inspection Parts

Clearance/Fit

Scratches/Dirt/

Harness

Interference

Installation/

Tightening/

Engagement

Operation

Check

Tow Harness Functions

Tow Harness

Tow Harness Module Ground
Screw

Driver’s Side Left Rear Interior
Trim Panel

Passenger Side Right Rear Interior
Trim Panel

Rear Threshold Plate

Rear Foam Inserts

Rear Floor Covering

Vehicle Negative Power Cable

4-FLAT Harness

50mm Between Exhaust & Harness

Inspect the installed / reinstalled parts for the following items:

0000-8E-R10

PART NUMBER:

2017 > CX-5 (GAS 2.5L)

APPLICABLE MODELS

Notes:
1.

Verify signal functionality at the trailer harness plug using test procedure on page 8.

Ensure tow harness module ground bolt is torqued to 7.0 N m.

Содержание 0000-8E-R10











Результаты поиска

Содержание 0000-8E-R10

Отзывы:

Похожие инструкции для 0000-8E-R10

Бренды по названию

Популярные бренды

Mazda 0000-8E-R10, Руководство по установке

Результаты поиска

Содержание 0000-8E-R10

Отзывы:

Похожие инструкции для 0000-8E-R10

Бренды по названию

Популярные бренды