Maytag Commercial MLG22PD Скачать руководство пользователя страница 26

Страница: 26 / 32

ELECTRONIC CONTROL SETUP INSTRUCTIONS

NOTE:

After the washer/dryer has been installed and connected

to electrical supply, the display will show “0 MINUTES” on the

washer and dryer portions of the display. After the washer and

dryer doors have been opened and closed, the display will show

the price for each machine. On washer/dryers set for free cycles,

the display sections will flash “SELECT CYCLE.”

PD Models:

Insert coins until “SELECT CYCLE” flashes on the

display portion of the washer or dryer that is to be run.

PN/PR Models:

Sent from the factory as Free Vend. If a debit

card reader is installed, then a debit card is required rather

than coins. Generation 1 or 2 debit card systems may be used;

but when the Generation 2 debit system is used, the controls

will automatically be set to Enhanced Debit mode (J. Ed). In

Enhanced Debit mode, the card balance will also display when

a debit card is inserted into the reader.

Door must be closed on the desired washer/dryer before cycle

selection is made.

Press the fabric setting button for the washer/dryer cycle

desired. After the cycle is started, the time will display and

count down.

If a cycle is interrupted by opening the door or power loss,

“RESELECT CYCLE” will flash in the display. To restart the

washer/dryer, close door and reselect desired cycle.

NOTE:

When set for free vend operation an ongoing dryer cycle

will cancel if the door is opened.

Washer Control

General Washer/Dryer User Information

SCROLLING “OUT OF ORDER” MESSAGE, FOLLOWED BY A

FAILURE OR DIAGNOSTIC CODE, SHOWING IN DISPLAY –

This

condition indicates the washer/dryer is inoperative. Diagnostic

codes being displayed on the upper portion of the display pertain

to the dryer section, and diagnostic codes displayed on the lower

portion of the display apply to the washer section. Diagnostic

codes displayed on both the upper and lower portions of the

display pertain to the control system of both the washer and dryer.

“0 MINUTES” SHOWING IN DISPLAY –

This indicates the

cycle is complete and the washer/dryer cannot be operated. Coins

dropped or debit inputs during this condition will be stored in

escrow but cannot be used until normal operation is restored by

opening and closing the door. If a door switch has failed, causing

“0 MINUTES” to remain in the display after the door is opened

and closed, it must be replaced before normal operation can be

restored.

COLD START (Initial first use) –

Washer/dryer is programmed

at the factory as follows:
Washer

11-minute wash period

1.75 wash price (PD models)

0.00 wash price (PN/PR models)

three rinses (extra rinse not enabled)

Dryer

5 minutes per coin for PD models

45 minutes dry time for PN/PR models

1.50 dry price (fixed cycle with top off –

PD Models)

0.00 dry price (fixed cycle – PN/PR Models)

Dryer Control

Содержание MLG22PD

































Результаты поиска

Содержание MLG22PD

Отзывы:

Похожие инструкции для MLG22PD

Бренды по названию

Популярные бренды

Maytag Commercial MLG22PD, Руководство по установке

Результаты поиска

Содержание MLG22PD

Отзывы:

Похожие инструкции для MLG22PD

Бренды по названию

Популярные бренды