manualshive.com logo in svg

Maytag Commercial MLG22PD, Руководство по установке, Страница: 12 / 32

Поделиться
Скачать
Maytag Commercial MLG22PD Скачать руководство пользователя страница 12

12

STACKED WASHER/GAS DRYER INSTALLATION  
REQUIREMENTS

Stacked Washer/Gas Dryer Gas Supply Requirements

Gas Supply

Before installation, check that the local gas distribution conditions, 

nature of gas and pressure, and the adjustment of the appliance 

are compatible. Burner information will be found on the model/

serial rating plate in the door recess of the dryer. If this information 

does not agree with the type of gas available, see your dealer. 

Natural Gas:

This dryer is factory adjusted for use with NATURAL GAS (G20), 

and no further adjustment should be required at installation.

L.P. Gas:

This dryer is also certified for use with L.P. gas with appropriate 

conversion. No attempt shall be made to convert the appliance 

from the gas specified on the model/serial rating plate for use  

with a different gas without consulting the serving gas supplier.
Conversion must be done by a competent service technician. 

L.P. Gas conversion kit, part number W10571757, is available for 

purchase from your dealer. Full instructions are supplied with the 

kit.

Supply line requirements:

Provide a rigid gas supply line to the washer/dryer location. It 

should be minimum 12.5 mm (1/2") ID. When acceptable to the 

gas supplier and local codes, 10 mm (3/8") ID rigid supply line 

may be used for lengths under 6.1 m (20'). Pipe-joint compounds 

resistant to the action of L.P. gas must be used.
Gas connection to the dryer itself should be made by means  

of a flexible gas hose suitable for the appliance and gas category 

in accordance with national installation regulations. If in doubt, 

contact the gas supplier. It should be minimum 10 mm (3/8") ID.
A means of restraint should be used between the washer/dryer 

and the wall to avoid straining of the rigid gas supply when the 

washer/dryer is moved. An appropriate length of chain and a wall 

hook is recommended.
The dryer gas inlet connection is a 3/8" NPT thread. An adapter is 

supplied for conversion to standard ISO 228-1 thread (3/8" BSP).
Check for leaks by using an approved noncorrosive leak-detection 

solution. Bubbles will show a leak. Correct any leak found. A 

pressure measurement tapping is provided on the gas valve  

within the dryer, accessible after removal of the lower front panel.
The dryer must be disconnected from the gas supply piping 

system during any pressure testing of that system.

Содержание MLG22PD

































Отзывы:

Нет отзывов