manualshive.com logo in svg

Maytag Commercial MLG22PD, Руководство по установке, Страница: 30 / 32

Поделиться
Скачать
Maytag Commercial MLG22PD Скачать руководство пользователя страница 30

30

ELECTRONIC CONTROL SETUP INSTRUCTIONS

C.20

VALUE OF COIN 2 (WASHER)

C.20

PD MODELS: This represents the value of coin 

2 in number of nickles. 20 = $1.00. Increase 

between 1 and 200 nickles by pressing the 

POWERWASH button and decrease by 

pressing the TEMPERATURE button.

C.05

PN/PR models only: For models using 

Enhanced Debit, this field represents the value 

of top off in nickles for the dryer, or $.25. 

Factory default of C.05; represents 5 x $.05, 

or $.25.
Press the EXTRA RINSE button once  

to advance to next code.

E.00

ADD COINS OPTION (WASHER)

 

This option is either selected On or not selected 

Off. This option causes the customer display 

to show the number of coins (Coin 1) to enter, 

rather than the dollars-and-cents amount.

E.00

Not selected Off.

E.AC

Selected On.
Press DELICATES button three consecutive 

times for this selection.
PN/PR models only: In enhanced debits mode,  

this option is not selectable. 
Press the EXTRA RINSE button once  

to advance to next code.

WASH UPGRADES (WASHER)
H.00 

COOL

COOL Temperature Upgrade Price—

Set between 0 and 200 by pressing the 

POWERWASH (increase) button or pressing 

the TEMPERATURE (decrease) button. 

Factory preset for 0 coins = $0.00.

H.00 

WARM

WARM Temperature Upgrade Price—

Set between 0 and 200 by pressing the 

POWERWASH (increase) button or pressing 

the TEMPERATURE (decrease) button. 

Factory preset for 0 coins = $0.00.

H.00 

HOT

HOT Temperature Upgrade Price—Set 

between 0 and 200 by pressing the 

POWERWASH (increase) button or pressing 

the TEMPERATURE (decrease) button.  

Factory preset for 0 coins = $0.00.

H.01 

EXTRA RINSE

EXTRA RINSE Upgrade Price—Set between  

0 and 200 by pressing the POWERWASH 

(increase) button or pressing the 

TEMPERATURE (decrease) button.  

Factory preset for 1 coins = $0.25.
Press the EXTRA RINSE button once to 

advance to next code.

J.Cd

COIN/DEBIT OPTION (WASHER)

J.Cd

Both coin and debit selected.

J.d

Debit card selected, coins disabled. Press the 

DELICATES button three consecutive times for 

this selection. 

J.C

Coins selected, debit disabled. Press the 

DELICATES button three consecutive times  

for this selection.

J.Ed

Enhanced Debit is self-selected when a 

Generation 2 card reader is installed in the 

washer. The Ed option cannot be manually 

selected or deselected.
Press the EXTRA RINSE button once to 

advance to next code.

L.00

PRICE SUPPRESSION OPTION 

(WASHER) 

This option causes the customer display to 

show “ADD” or “AVAILABLE” rather than the 

amount of money to add. (Used mainly in debit 

installations.)

L.00

Not selelcted Off.

L.PS

Selected On. Press the DELICATES button 

once for this selection.
Press the EXTRA RINSE button once  

to advance to next code.

n.CE

CLEAR ESCROW OPTION (WASHER)

 

When selected, money held in escrow for 30 

minutes without further escrow or cycle activity 

will be cleared.

n.CE

Selected On.

n.00

Not selected off. Press the DELICATES button 

once to deselect this selection.
Press the EXTRA RINSE button once to 

advance to next code.

r.800

TOP SPIN SPEED RPM (WASHER)

r.800

This can be selected from the following spin 

speeds: 600 rpm, 750 rpm, 800 rpm, 1000 

(displays as 999) rpm. Step between speeds 

by pressing the DELICATES button. Factory 

default of 800 rpm.
Press the EXTRA RINSE button once  

to advance to next code.

U.00

PENNY INCREMENT OFFSET (DRYER)

U.00

This represents the penny increment price 

offset used in Generation 2 (Enhanced Debit) 

PN/PR models. Choose from 0-4 pennies by 

pressing the HEAVY DUTY button.

U.00

COIN (HUNDREDTH) INCREMENT OFFSET 

(WASHER)

U.00

This represents the penny increments price 

offset used in Generation 2 (Enhanced Debit) 

PN/PR models. Increase from 0-4 pennies by 

pressing the POWERWASH button decrease 

by pressing TEMPERATURE button.
Press the EXTRA RINSE button once to 

advance to next code.

CYCLE SETTINGS (WASHER)
A1.03

PREWASH LENGTH

 

This is the number of minutes of PREWASH. 

Set between 2 and 7 by pressing the 

POWERWASH (Increase) button or pressing 

the TEMPERATURE (decrease) button.
Press the EXTRA RINSE button once to 

advance to next code.

A2.03

FINAL SPIN LENGTH

 

This is the number of minutes of final high-speed 

spin. Set between 3 and 8 by pressing the 

POWERWASH (increase) button or pressing 

the TEMPERATURE (decrease) button.
Press the EXTRA RINSE button once to 

advance to next code.

Содержание MLG22PD

































Отзывы:

Нет отзывов