background image

i-SHWAK V4 

Inverter air/water chillers and heat pumps with wall-mounted indoor unit and remote condensing outdoor unit 

4.4

 

REFRIGERANT SAFETY DATA SHEET 

 

Name: 

R410A (50% Difluoromethane (R32); 50% Pentafluoroethane (R125). 

RISKS IN DICATIONS 

Major risks: 

Asphyxia 

Specific risks: 

The rapid evaporation can cause freezing.

 

FIRST AID 

General information: 

Never give anything by mouth to an unconscious person.

 

Inhalation: 

Outdoors open transport. 

 

Use oxygen or artificial respiration if necessary. 

 

Do not give adrenaline or similar drugs 

Eyes contact: 

Rinse carefully with water for at least 15 minutes and consult a doctor. 

Contact with skin: 

Wash immediately with plenty of water. 

 

Take off immediately the contaminated clothes. 

FIRE PREVENTION 

Extinguishing Media: 

Whatever. 

Specific risks: 

Increase in pressure. 

Specifics methods:  

Use

 

water spray

 to 

cool containers

 

MISURE IN CASO DI FUORIUSCITA ACCIDENTALE 

Personal precautions: 

Evacuate personnel to safe areas. 

 

Provide adequate ventilation. 

 

Use personal protective equipment. 

Environmental precautions: 

Evaporate. 

Cleaning method:  

Evaporate. 

MANIPULATION AND STORAGE 

Manipulation 

 

Action/technical precautions:  

Provide sufficient air exchange and/or exhaust in work rooms. 

Recommendations for safe use: 

Do not breathe vapors or spray mist. 

Storage: 

Close tightly and store in a cool, dry and well ventilated place. 

 

Store in original container. Incompatible products: explosive, flammable materials, Organic peroxide 

EXPOSURE CONTROL / PERSONAL PROTECTION 

Control parameters:  

AEL (8-h e 12-h TWA) = 1000 ml/m³ for each of the two components. 

Respiratory protection: 

For rescue and maintenance operation in storage tanks use self-contained respirator apparatus. 

 

The vapors are heavier than air and can cause suffocation by reducing oxygen available for breathing. 

Eyes protection:  

Safety glasses. 

Protection of hands:  

Rubber gloves. 

Hygiene measures: 

Do not smoke. 

PHYSICAL AND CHEMICAL PROPERTIES 

Colour: 

Colourless. 

Odor: 

Light. 

Boiling point: 

-52.8°C at atmospheric pressure. 

Lighting point: 

do not ignite. 

Density: 

1.08 kg/l at 25°C. 

Solubility in water: 

Negligible. 

STABILITY AND REACTIVITY 

Stability:  

No reactivity when used with the appropriate instructions. 

Materials to avoid:  

Highly oxidizing materials. Incompatible with magnesium, zinc, sodium, potassium and aluminum. 

 

The incompatibility is more serious if the metal is present in powdered form or if the surfaces were, recently, unprotected. 

Decomposition products 

These products are halogenated compounds, hydrogen fluoride, carbon oxides (CO, CO2), carbonyl halides. 

Risks: 

 

TOXICOLOGICAL INFORMATION 

Acute toxicity: 

(R32) LC50/ inhalation /4 hours/on rat >760 ml/l 

 

(R125) LC50/ inhalation /4 hours/on rat >3480 mg/l 

Local effects: 

Concentrations substantially above the TLV may cause narcotic effects. 

 

Inhalation of decomposed products of high concentrations may cause respiratory failure (pulmonary edema). 

Long term toxicity: 

Did not show carcinogenic

teratogenic

 or 

mutagenic effects

 in 

animal

 

experiments

ECOLOGICAL INFORMATION 

Global warming potential 

2088 

GWP (R744=1): 

 

Ozone Depletion Potential 

Ozone ODP (R11=1): 

 

Disposal considerations: 

Usable with reconditioning. 

 

Содержание ADVANTIX i-SHWAK V4 06

















































Отзывы: