DIGITAL PLUNGE ROUTER - 054-6902-0
DIGITAL PLUNGE ROUTER - 054-6902-0
21
22
LED worklights
(fig 8)
Your router motor has 3 built-in worklights located
around the collet/nut to provide high visibility of
the workpiece when cutting. These lights are
always “On” when the toggle switch is in the “ON”
position.
Setting the router
(fig 9)
WARNING!
When setting the router; make sure
to turn the toggle on/off switch to the
“OFF” position. Failure to do so could
result in accidental starting.
1. Place the router on a flat workpiece; make sure
that the bit is not contacting the workpiece.
2. Turn the toggle on/off switch to the “OFF”
position.
3. Connect the digital router to a power source:
the LCD screen displays the specifications of the router (fig 9).
4. Press “SET”: bit profiles are displayed. Press “+” or “–” to choose the bit type needed.
5. Press “SET” again: bit sizes are displayed. Press “+” or “–” to choose the bit size needed.
6. Press “SET” again: workpiece materials are displayed. Press “+” or “–” to choose the material of
the workpiece to be cut.
7. Press “SET” again to exit the setting system.
8. The optimum speed is computed and displayed on the digital screen.
9. Turn the toggle on/off switch to ON.
10. The motor will run at the pre-set speed.
NOTICE:
If the operator wants to control the speed manually, Press “+” or “–” to choose speed without
pressing the “SET” key.
NOTICE:
When the motor is running, the “SET” key is not functional. The operator can only select “+”
or “–” to change the speed.
Quick-release edge guide
(fig 6)
WARNING!
Your router should never be turned on
or be connected to the power source
when you are assembling parts, making
adjustments, installing or removing collets/
nuts and cutter bits, cleaning or when it is
not in use. Disconnecting the router will
prevent accidental starting, which could
cause serious personal injury.
This router is equipped with a quick-release edge guide. This is an effective aid to cutting straight lines when
chamfering or grooving.
1. Turn the motor off and unplug the router from the power source.
2. Loosen the wing nuts on the router base plate.
3. Feed the bars on the edge guide through the holes in the base plate, and then tighten the wing nuts.
4. Press the two release buttons on the edge guide at the same time, and adjust the distance between
the router bit and the edge guide by moving the guide until it is situated at the proper distance from
the cutter bit.
5. Release the release button to hold the straight edge guide in position.
Toggle “on/off” switch
(fig 7)
Your router motor is turned “ON” and “OFF” with
the toggle switch located on the top cap of the
motor housing.
The left side of the toggle switch hood (as you face
it) is marked “I” for “ON” and the right side (as you
face it) is marked “O” for “OFF”.
To turn the motor “ON”, push the toggle switch to
the left side marked “I”, or “ON”. To turn the motor
“OFF” push the toggle switch to the right side
marked “O”, or “OFF”.
Always hold the router and the cutter bit away from the workpiece when turning the toggle switch
“ON.” Only contact the workpiece with the router and cutter bit after the router has reached full speed.
Only remove the router and cutter bit from the workpiece after turning the router motor “OFF” and the
cutter bit has come to a complete stop.
OPERA
TING INSTR
UCTIONS
OPERA
TING INSTR
UCTIONS
fig 6
Release
Buttons
Release
Buttons
Wing Nut
fig 8
fig 7
fig 9
Содержание 054-6902-0
Страница 1: ...INSTRUCTION MANUAL DIGITAL PLUNGE ROUTER 054 6902 0...
Страница 24: ......
