Masport Calais Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 69

background image

Page 52

ON/OFF

Switch

Fan Speed

Switch

(Rear View)

Wires to

Fan Switch

Connectors

Self-adhesive

Wire Clip

For Gas

Connection

Wires to

On/Off

Switch

POWER CORD (3ft)

Diagram 3

INSTALLATION INSTRUCTIONS

Diagram 1: Faceplate Assembly

Trim

Clips

Diagram 2: Trim Assembly

FACEPLATE & TRIM INSTALLATION

this point, do a trial fit to the unit. Make any neces-
sary adjustments and when it fits properly then
tighten down the screws.

3) Using the trim clips provided, join the left side trim

(with the ON/OFF switch) to the top trim. See
diagram 2. Connect the right side trim to the top
trim.

4) Place the trim on the assembled faceplate panels,

aligning the wire connections from the switches
with the notch on the left side panel.

5) Connect the fan switch wires by taking the black

and red wires with the male ends (in the grey
harness) and connect them with the wire connec-
tors from the fan speed control.

1) Lay the faceplate panels flat, facedown on some-

thing soft so they don't scratch.

2) a)

Take the top faceplate and align the holes in
it with the holes in the side panels. Using the
screws provided, attach from the top of the
panel (holes in the top panel are slightly
larger than the holes in the side panel to
facilitate easier installation). See diagram 1.

b)

4"(102mm) Hearth Trim. Attach the Hearth
Trim to the bottom of the faceplate side
panels with the screws provided. See dia-
gram 1.

Hint: Don't tighten the screws down completely at

6) Connect the ON/OFF switch wires by taking the

black and red wires with the female ends and
connect them to the ON/OFF switch.

7) Install these wires in the clips on the left faceplate

to ensure they dont touch the insert. See diagram
3.

8) The power cord should be run behind the

faceplate panel from the U31/I31 to electrical outlet
box.

«
...
50
51
52
53
54
...
»

Содержание Calais






































































Отзывы:

Нет отзывов

Похожие инструкции для Calais

Бренд: Calcana Страницы: 96

Бренд: Jandy Pro Series Страницы: 4

Бренд: UNITED Страницы: 8

Бренд: DAXOM Страницы: 20

Бренд: RADtec Страницы: 15

Бренд: ACDC Страницы: 3

Бренд: Electrorad Страницы: 16

Бренд: Medallion Страницы: 20

Бренд: Vogel & Noot Страницы: 8

blueheat airtop 2000

Бренд: Webasto Страницы: 24

Бренд: Comfort Glow Страницы: 40

Appino BEATZZ Series

Бренд: Vasner Страницы: 80

Бренд: JENFORT Страницы: 12

Бренд: A.O. Smith Страницы: 8

Eco GAUS-160FQTS

Бренд: Sanden Страницы: 20

Бренд: EUROM Страницы: 36

Бренд: Draper Страницы: 20

Бренд: Kenmore Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды