background image

TEMPERATURE CONTROLLER -5002U-P 

 

 

REF NO: m55A/om/201 

 

 

Issue NO: 03 

 

 

 

Page 

29

 of 

35

 

 

10.2  PV input sensor calibration 

When  user  enters  in  calibration  menu,  PV  display  shows  message 

tc.l.s

 

(Thermocouple/Linear  Span)  for  sensor  input  span  calibration  for  Thermocouple  and 
Linear input type.Feed sensor input using a calibrator, such that process value is close 
to upper range value. 

 

Note:

 The controller allows the user to calibrate se

nsor‟s input anywhere in the range, 

but it is recommended that it should be calibrate the input at points close to lower and 
upper range values. 

 

DP of last digit will blink to indicate that the value can be changed. Use Inc/Shift key to 
correct  the  displayed  reading  to  the  desired  process  value  and  press  ENT  key.  The 
controller will display message 

wait

 (wait) in the SV display to indicate that it is doing 

the necessary calculations. 
When  the  calculations  are  over,  the  new  calibration  values  are  stored  automatically. 
For TC and Linear input type user has to calibrate SPAN only. 
FOR RTD input user has to calibrate ZERO and SPAN. 
PV  shows  the  message 

RTD.Z

  (calibration  Zero).  SV  display  shows  process  value 

corresponding to input sensor value and old calibration data. Feed sensor input using 
a  calibrator,  such  that  process  value  is  close  to  sensor‟s  lower  range  value.  Use 
Inc/Shift  key  to  arrive  at  the  desired  process  value.  Press  ENT  key  to  register  the 
changes. 
The controller will display message 

wait

 (wait) in the SV display to indicate that it is 

doing  the necessary  calculations.  Depending  on  the  situation,  this process may  take 
few seconds to calibrate. 
Once zero is calibrated, press MENU key for RTD span calibration. 

 

PV  shows  the  message 

RTD.S

  (rtd.S)  (calibration  Span).  SV  display  shows  process 

value corresponding to input sensor value and old calibration data. Feed sensor input 
using a calibrator, such that process value is close to sensor‟s upper range value. Use 
Inc/Shift  key  to  arrive  at  the  desired  process  value.  Press  ENT  key  to  register  the 
changes. 

 

The controller will display message 

wait

 (wait) in the SV display to indicate that it is 

doing the necessary calculations. When the calculations are over, the new calibration 
values are stored automatically. In case, the controller cannot complete the calibration 
due  to  any  reason,  it  will  hold  previous  calibration  parameters.  Calibration  for  input 
sensor is over. 

10.3  Retransmission1  and  Retransmission2output  calibration  (Voltage/current 
output) 

Press MENU key repeatedly, till PV display shows message 

rt1.Z

 (Retransmission1 

output zero calibration). 
SV  display  shows  the  value  being  outputted  on  Retransmission  output  terminals. 
Measure  the  value  using  a  highly  accurate  digital  multi  meter.  Use  Inc/Shift  key  to 
correct  the  displayed  reading  to  the  measured  value.  Press  ENT  key.  The  controller 
will  store  zero  calibration  value.  Press  MENU  key  to  calibrate  retransmission  output 
span calibration menu. 

 

PV shows the message 

rt1.S

(Retransmission1 output  span calibration). SV display 

shows  the  value  being  outputted  on  retransmission  output  terminals.  Measure  the 
value. Use Inc/Shift key to correct the displayed reading to the measured value. Press 
ENT  key.  When  the  calculations  are  over,  the  new  calibration  values  are  stored 

Содержание 5002U-P




































Отзывы: