Marvell Integrated Controller 88F6281 Скачать руководство пользователя | Manualshive

Страница: 51 / 140

background image

Pin Multiplexing

Multi-Purpose Pins Functional Summary

Copyright © 2008 Marvell

Doc. No. MV-S104859-U0 Rev. E

December 2, 2008, Preliminary

Document Classification: Proprietary Information

Page 51

4

Pin Multiplexing

4.1

Multi-Purpose Pins Functional Summary

The 88F6281 device contains 50 Multi-Purpose Pins (MPP). Each one can be assigned to a different
functionality through the MPP Control register.

General Purpose pins: MPP[5:0] and MPP[49:7]:

•

GPIO (input/output): MPP[0], MPP[4], MPP[9:8], MPP[11], MPP[17:13], MPP[32:20], and
MPP[49:34]

•

GPO (output): MPP[3:1], MPP[5], MPP[7], MPP[10], MPP[12], MPP[19:18], and MPP[33]

SYSRST_OUTn: Reset request from the device to the board reset logic. This pin is an output.
SYSRST_OUTn is the default setting for MPP[6].

PEX_RST_OUTn: Optional PCI Express Endpoint card reset output.

MII/MMII/GMII/RGMII interface signals

SATA0/1_ACTn/SATA0/1_PRESENTn (port 0 and port 1): SATA active and SATA present
indications—see the SATA section in the 88F6180, 88F6190, 88F6192, and 88F6281
Functional Specifications.

NF_IO[7:0] (NAND Flash data [7:0])

SPI interface: SPI_MOSI, SPI_MISO, SPI_SCK, SPI_CSn

UART interface (port 0 and port 1): Transmit and receive functions: UA0_TXD, UA0_RXD,
UA1_TXD, UA1_RXD, and Modem control functions: UA0_RTSn, UA0_CTSn, UA1_RTSn,
UA1_CTSn

SDIO interface: SD_CLK, SD_CMD, SD_D[3:0]

Audio interface signals: AU_SPDIFI, AU_SPDIFO, AU_SPDIFRMCLK, AU_I2SBCLK,
AU_I2SDO, AU_I2SLRCLK, AU_I2SMCLK, AU_I2SDI, AU_EXTCLK

TS (Transport Stream) interface signals: TSMP[12:0]

TDM/SPI interface signals: TDM_CH0/2_TX_QL, TDM_CH0/2_RX_QL, TDM_SPI_CS0/1,
TDM_SPI_SCK, TDM_SPI_MOSI, TDM_SPI_MISO, TDM_CODEC_INTn,
TDM_CODEC_RSTn, TDM_PCLK, TDM_FS, TDM_DRX, TDM_DTX

PTP signals: PTP_EVENT_REQ, PTP_TRIG_GEN, PTP_CLK

TWSI signals: TW_SDA, TW_SCK

«
...
49
50
51
52
53
...
»

Содержание Integrated Controller 88F6281













































































































































Отзывы:

Нет отзывов

Похожие инструкции для Integrated Controller 88F6281

Бренд: Vacon Страницы: 62

Бренд: CAME Страницы: 32

Бренд: Babybee Prams Страницы: 21

Бренд: Canarm Страницы: 3

Бренд: Zodiac Страницы: 12

Бренд: National Instruments Страницы: 34

Бренд: Dantherm Страницы: 20

Бренд: MaintTech Страницы: 28

Бренд: Procom Страницы: 10

Бренд: Wilo Страницы: 128

Бренд: Intellitec Страницы: 16

Бренд: York Страницы: 2

Бренд: Hahnel Страницы: 36

Бренд: maxon motor Страницы: 44

Бренд: Resol Страницы: 32

Бренд: Aerotech Страницы: 36

Бренд: Italtecnica Страницы: 16

Бренд: ZKTeco Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды