Marvell Integrated Controller 88F6281 Скачать руководство пользователя

Страница: 5 / 140

Features

Doc. No. MV-S104859-U0 Rev. E

December 2, 2008, Preliminary

Document Classification: Proprietary Information

Page 5

•

Priority queuing on receive based on Destination
Address (DA), VLAN Tag, and IP TOS

•

Layer 2/3/4 frame encapsulation detection

•

TCP/IP checksum on receive and transmit

•

Supports proprietary 200 Mbps Marvell MII (MMII)
interface

•

Supports four modes:

Port 0 RGMII, Port 1 RGMII

Port 0 RGMII, Port 1 MII/MMII

Port 0 MII/MMII, port 1 RGMII

Port 0 GMII, Port 1 N/A

•

DA filtering

Precise Timing Protocol (PTP)

•

Supports precise time stamping for packets, as
defined in IEEE 1588 PTP v1 and v2 and IEEE
802.1AS draft standards

•

Supports Flexible Time Application interface to
distribute PTP clock and time to other devices in
the system

•

Optionally accepts an external clock input for time
stamping

Audio Video Bridging networks

•

Supports IEEE 802.1Qav draft Audio Video
Bridging networks

•

Supports time- and priority-aware egress pacing
algorithm to prevent bunching and bursting
effects—suitable for audio/video applications

•

Supports Egress Jitter Pacer for AVB-Class A and
AVB-Class B traffic and strict priority for legacy
traffic queues

USB 2.0 port

•

Serves as a peripheral or host

•

USB 2.0 compliant

•

Integrated USB 2.0 PHY

•

Enhanced Host Controller Interface (EHCI)
compatible as a host

•

As a host, supports direct connection to all
peripheral types (LS, FS, HS)

•

As a peripheral, connects to all host types (HS, FS)
and hubs

•

Up to four independent endpoints, supporting
control, interrupt, bulk, and isochronous data
transfers

•

Dedicated DMA for data movement between
memory and port

Two Integrated Marvell 3 Gbps (Gen2i) SATA PHYs

•

Compliant with SATA II Phase 1 specifications

Supports SATA II Native Command Queuing
(NCQ), up to 128 outstanding commands per
port

Fully supports first party DMA (FPDMA)

Backwards compatible with SATA I devices

•

Supports SATA II Phase 2 advanced features

3 Gbps (Gen2i) SATA II speed

Port Multiplier (PM)—Performs FIS-based
switching, as defined in SATA working group PM
definition

Port Selector (PS)—Issues the protocol-based
Out-Of-Band (OOB) sequence for selecting the
active host port

•

Supports device 48-bit addressing

•

Supports ATA Tag Command Queuing

SATA II Host Controller

•

Enhanced-DMA (EDMA) for the SATA ports

•

Automatic command execution, without host
intervention

•

Command queuing support, for up to 32
outstanding commands

•

Separate SATA request/response queues

•

64-bit addressing support for descriptors and data
buffers in system memory

•

Read ahead

•

Advanced interrupt coalescing

•

Target mode operation—supports attaching two
88F6281 controllers through their Serial-ATA ports,
enabling data communication between the
88F6281 controllers

•

Advanced drive diagnostics via the ATA SMART
command

Cryptographic engine

•

Hardware implementation on encryption and
authentication engines, to boost packet processing
speed

•

Dedicated DMA to feed the hardware engines with
data from the internal SRAM memory or from the
DDR memory

•

Implements AES, DES, and 3DES encryption
algorithms

•

Implements SHA1 and MD5 authentication
algorithms

S/PDIF / I

S Audio In/Out interface

•

Either S/PDIF or I

S inputs can be active at one

time

•

Both S/PDIF and I

S outputs can be

simultaneously active, transferring the same PCM
data

S/PDIF-specific features

•

Compliant with 60958-1, 60958-3, and IEC61937
specifications

•

Sample rates of 44.1/48/96 kHz

•

16/20/24-bit depths

Содержание Integrated Controller 88F6281













































































































































Результаты поиска

Содержание Integrated Controller 88F6281

Отзывы:

Похожие инструкции для Integrated Controller 88F6281

Бренды по названию

Популярные бренды

Marvell Integrated Controller 88F6281, Технические характеристики

Результаты поиска

Содержание Integrated Controller 88F6281

Отзывы:

Похожие инструкции для Integrated Controller 88F6281

Бренды по названию

Популярные бренды