background image

 

Technical Specifications  

21 

 

*Measurements made at nominal voltage. Allow for a deviation of +/- 10% 

T h e r m a l  

Exterior surface temperature, steady state ........................................ 50° C (122 °F) 
Maximum ambient temperature (Ta max) .......................................... 40° C (104° F) 
Maximum nozzle temperature.......................................................... 200° C (392° F) 
Minimum ambient temperature (Ta min) ............................................... 5° C (41 °F) 

Ap p r o v a l s  

 

EU Model 

EU safety: .................................................................  EN 60 335-1+A15, EN 62233 
EU EMC: ..............................................................................................EN 61000-6-3 
EU immunity: .......................................................................................EN 61000-6-1 
Australia/NZ (pending): ..................................................................................... RCM 

US Model 

US Safety ...................................................................................................... UL 998 
Canadian Safety ................................................................... CSA C22.2 No. 104.01 
 

 

 

I n c l u d e d   I t e m s  

Analog remote control ....................................................................... P/N 92765038 
Fluid reservoir, 9.5 l ............................................................................ P/N 34300528 
Power input cable, EU, Neutrik PowerCON, stripped ends, 2.5 m (8.2 ft.) 
 ........................................................................................................... P/N 11501041 
Power input cable, US, Neutrik PowerCON, molded NEMA 5-15P, 2.5 m (8.2 ft.) 
 ........................................................................................................... P/N 11501042 
User manual ....................................................................................... P/N 35010032 

Ac c e s s o r i e s  

JEM™ ZR44 Digital Remote Control .................................................. P/N 92765037 
JEM™ ZR44 Ducting Kit with 5 m (16.4 ft.) ducting ........................... P/N 92625005 
JEM™ ZR44 Drip Tray ........................................................................ P/N 92620011 

Approved Fluids 

JEM™ Pro Smoke Studio 
JEM™ Pro Smoke Super

 

JEM™ Pro Smoke High Density 
JEM™ i-fog Fluid 
JEM™ Pro Steam Simulation Fluid

 

JEM™ Pro Clean Supreme Fluid 

 *Various sizes available - contact your dealer or see martin.com for more details. 

Installation Hardware 

Half-coupler clamp ............................................................................. P/N 91602005 
G-clamp (vertical hanging suspension only) ..................................... P/N 91602003 
Quick trigger clamp (vertical hanging suspension only) ................... P/N 91602007 

Service Tools 

Epsilon 5 AVR Programmer ............................................................... P/N 50502004 

Temperature Calibration Box ............................................................. P/N 92620005 

O r d e r i n g   i n f o r m a t i o n  

JEM™ ZR44 Hi-Mass™, EU ................................................................ P/N 92215300 
JEM™ ZR44 Hi-Mass™, US ................................................................ P/N 92215310 

Содержание JEM ZR44 Hi-MASS





























Отзывы: