manualshive.com logo in svg

Mantis ComposT-Twin Series, Руководство пользователя

Поделиться
Скачать
Mantis ComposT-Twin Series Скачать руководство пользователя страница 6

Assembly of the ComposT-Twin is divided into two major sub-assemblies:

Support frame 

and

Drum

Tools needed for assembly of ComposT-Twin

✔  

Hammer or rubber mallet

✔  

3/8” wrench

✔  

3/4” wrench

✔  

Regular screwdriver (flat head)

✔  

7/16” wrench

✔  

Phillips screwdriver (cross head)

✔  

7/16” socket wrench

✔  

Wheel bearing-type grease

The ComposT-Twin is easiest to assemble with TWO PEOPLE sharing and 
coordinating the work. Allow 1-2 hours to assemble the entire composter. 

Begin with the Support Frame Assembly.

Tools needed for Support Frame Assembly:  

Hammer or rubber mallet and 3/4” wrench.

Find a large, shaded area outside your house
or in your garage to assemble the Support 
Frame. 

DO NOT ASSEMBLE THE SUPPORT

FRAME IN YOUR LIVING ROOM, AS YOU
WON’T BE ABLE TO GET IT THROUGH 

THE DOOR WHEN YOU ARE DONE!

SAFETY WARNING

THE DIMENSIONS OF THE ASSEMBLED

SUPPORT FRAME ARE 35” HIGH X 56”

LONG X 41” WIDE. BE SURE TO ASSEMBLE

THE SUPPORT FRAME IN A GARAGE OR 

OPEN AREA WHERE YOU WILL BE ABLE TO

MOVE IT EASILY ONCE YOU ARE FINISHED.

▲

!

▲

!

6

Содержание ComposT-Twin Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды