manualshive.com logo in svg

Mantis ComposT-Twin Series, Руководство пользователя

Поделиться
Скачать
Mantis ComposT-Twin Series Скачать руководство пользователя страница 15

Attach 3rd and 4th panels the same way 
to complete the first chamber assembly.
Assemble the sheet metal panels for the 
second chamber using the same procedure.

Position mesh screen (key #23) onto the vent
hole of the end cap. Affix it using the zip
twist pal nut (key #27). Repeat this step with
the second end cap.

Correct assembly of the body of the first
chamber is very important. Beginning at the
arrow located inside the end cap, position
the rib of the 1st panel (key #19) in the
alignment slot. Bend the panels counter-
clockwise with ribs inside (the vent opening
in the end cap should be across from the
door opening, 2nd panel (key #18).

Continue to fit the edge of the sheet metal
into the opening formed by the inside edge
of the end cap and vertical ribs to form the 
chamber. Overlap the last joint and align the
slots. Fasten the last joint using shoulder
bolts (brass colored, key #32), nylon insert
lock nuts (key #33), Phillips head screwdriver
and 3/8” wrench.

Step 19

Step 20

Step 21

Step 22

15

Vent hole

Door opening

(key #18)

First panel

(key #19)

Содержание ComposT-Twin Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды