manualshive.com logo in svg

Mantis ComposT-Twin Series, Руководство пользователя

Поделиться
Скачать
Mantis ComposT-Twin Series Скачать руководство пользователя страница 20

Put self-tapping screw (key #26) into the 
cavity in the middle of the breather cap. Be
sure that the screw’s tip is coming out of the
hole. Place the breather screen (key #16) on
the front side of the door, covering the
round opening. 

Position the
breather cap
(key #15) on
the inside of 
the door (key
#17), over the
breather screen.
Place the tip of
the cap’s boss
inside the
hollow part of
the screen’s
boss. Hold breather cap and attach these two
parts with self-tapping screw using Phillips
head screwdriver. Apply some pressure on
the screw head to start thread cutting opera-
tion. Repeat this step and assemble breathers
at all four locations.

Hold door horizontally and fit door hooks
through the openings above the door panel.
Close the doors on the drum to cover door
opening and check the position of the
breather screens.

Step 42

Step 44

20

Lift the drum assembly and position on 
the bottom frame. Adjust gears and middle
wheels so that gear teeth mesh with the
corresponding end cap teeth, and the
middle divider edge fits into the middle
wheel groove.

SAFETY WARNING

COMPOSTER DRUM IS VERY HEAVY -

BE CAREFUL WHEN LIFTING. AT LEAST 

TWO PEOPLE ARE NEEDED TO LIFT DRUM

AND POSITION ON SUPPORT FRAME

▲

!

▲

!

Step 41

Step 43

Содержание ComposT-Twin Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды