manualshive.com logo in svg

Mantis ComposT-Twin Series, Руководство пользователя

Поделиться
Скачать
Mantis ComposT-Twin Series Скачать руководство пользователя страница 11

Choose the corner for the handle (this deci-
sion is entirely a factor of your convenience).
Place the end of the handle assembly inside
the axle rod at that corner, and align the
holes of the handle and axle rod. Gently
drive spring pin (key #11) through the holes
using a hammer or rubber mallet.  

Drive the spring pins through the holes in
the three other corners of the frame. The
spring pin should extend an equal amount
on each side of the axle rod. Line up the 
pin opening in the gear (key #7) with the
corresponding pin and slide the gear over it.
Repeat this step with each gear. 

TIGHTEN

ALL NUTS AND BOLTS SECURELY.

The support frame for your

Mantis ComposT-Twin is ready!

Place the frame on level ground,
where you want the composter to be
located in your yard. Lubricate the
four axle rod guide sections with
wheel bearing-type grease.

SAFETY WARNING

A SLANTED OR UNEVEN POSITION CAN MAKE

THE LOADED COMPOSTER UNSTABLE AND

HARDER TO TURN. BE SURE TO PLACE THE SUP-

PORT FRAME ON LEVEL GROUND

▲

!

▲

!

Step 12

Step 13

Step 14

11

Содержание ComposT-Twin Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды