manualshive.com logo in svg

Mantis ComposT-Twin Series, Руководство пользователя

Поделиться
Скачать
Mantis ComposT-Twin Series Скачать руководство пользователя страница 18

Pick up the sheet metal
assembly of the second
chamber and place it on top
of the divider to align with
the door of the first chamber.

Bend the assembly with the
ribs inside and fit the edge
of the sheet metal into the
opening formed by the
inside edge of the divider
and the vertical ribs. Door
openings should be located
side by side. 

Overlap the last joint and
align the slots. Fasten the
last joint using shoulder
bolts (brass colored, key
#32), nylon insert lock nuts
(key #33), Phillips head
screwdriver and 3/8”
wrench.  

Find the two sets of mounting holes on the
drum’s 3rd panel (key #20) of the second
chamber. Attach latches (key #24) to the
panel using screws (key #28), flat washer
(key #29) and nut (key #30), as shown. Make
sure that the hook part of the latch is point-
ing up towards the door panel.

Step 32

Step 33

Step 34

Step 35

18

Step 36

Remove the disposable
red protective covers
from the end of each
threaded rod and discard.

Содержание ComposT-Twin Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды