manualshive.com logo in svg

Mantis ComposT-Twin Series, Руководство пользователя

Поделиться
Скачать
Mantis ComposT-Twin Series Скачать руководство пользователя страница 14

19

18

20

21

There are two different types of ribs on the panels: one rib is straight, the other is clip-shaped.
Place panels on a flat ground surface with the ribs facing up, in the following order: 

The two slots of the 

drum 1st panel

(key #19) should be next to the door opening (key #18). 

The clip-shaped rib of the 2nd panel (key #18), 

door opening

, should face the 1st panel.

The 4 latch holes of the 

drum 3rd panel

(key #20) should be next to the flat rib of the 2nd panel.

The clip-shaped rib of the 

drum 4th panel

(key #21) should be next to the drum 3rd panel.

Place the drum’s 1st panel in a position where
the straight rib is facing the door panel’s clip-
shaped rib. Align outside edges to align holes.
Slide the clip-shaped rib of the door panel
over the straight rib of the drum’s 1st panel,
matching up the holes. If necessary, tap into
place with a hammer or rubber mallet. 

Fasten panels using screw (key #28), flat
washers (key #29),  and keps nut (key #30).
Tighten screws using 3/8” wrench and a flat
head screwdriver.

Step 16

Step 17

Step 18

SAFETY WARNING

USE OF A HAMMER ON DRUM PANELS MAY

DAMAGE PAINT. COVER PANEL EDGE WITH

A CLOTH BEFORE USING HAMMER.

▲

!

▲

!

1st panel has

2 door slots

2nd panel

door opening

3rd panel has

4 latch holes

4th panel has one

clip-shaped rib

14

Clip-shaped rib

Содержание ComposT-Twin Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды