background image

AVS S-SERIES INSTALLATION MANUAL - GEN 2 VER 5 

 

15 

 

Changing programmable features 

 

 

The AVS S-Series programming mode is very quick and easy to use. Follow the steps below to change any of the 
programmable features: 

 

1.

 

Find the Register (1 or 2) in which the feature is located. 

 

2.

 

Set  the  vehicle  up  as  described  to  access  the  required  Register.  e.g.  to  access  Register  1  close  all  doors, 
bonnet and boot, arm and disarm alarm then turn ignition on, off and back on. 

 

3.

 

Press  the 

  button  on  the  remote  the  number  of  times  for  the  function  you  wish  to  change.  

e.g. for arm and disarm chirps press the 

 button two times. Each press of the button will be confirmed 

by a flash of the indicators and dash LED and a chirp from the siren if connected. 

 

4.

 

Turn the ignition off. 

 

5.

 

The system will then confirm whether the feature is on or off. If the feature is enabled (turned on) the siren 
will chirp once. If the feature is disabled (turned off) the siren will chirp twice. 

 

Programming features Register 1 

 

Vehicle set up:        Close all doors, bonnet & boot, arm & disarm alarm then turn ignition on, off & on. 

 

Feature: 

Arm and disarm chirp (S5/S4) 

Press the 

 button 

this many times:

 

Factory setting: 

ON 

Description: 

One chirp on arm and two chirps on disarm. 

Feature: 

Door lock on ignition 

Press the 

 button 

this many times:

 

Factory setting: 

OFF 

Description: 

When  this feature is ON, the doors will lock when the ignition is turned on, and unlock 
when the ignition is turned off. 

Feature: 

No door ajar warning 
Use if the car has factory interior light delay 

Press the 

 button 

this many times:

 

Factory setting: 

OFF 

Description: 

When this feature is ON, the door ajar warning feature is removed so the indicators and 
siren  will  not  chirp  for  three  seconds  if  the  door  is  left  open.  It  will  ignore  the  door, 
bonnet/boot & aux circuits for 45 seconds upon arming. 

Feature: 

Perimeter night light 

Press the 

 button 

this many times:

 

Factory setting: 

OFF 

Description: 

When this feature is ON, the indicators will stay on constantly for 20 seconds on disarm, 
or until the ignition is turned on. This allows for illumination around the vehicle at night. 

 

Содержание AVS S Series





































Отзывы: