Malone MPG460XT, Руководство пользователя

Страница: 14 / 37

MPG460XT
800-295-0042 ext 206
technical@maloneautoracks.com
12
15. Install the wiring harness extension
through the tongue.
The easiest way is to let gravity pull the
harness through. Make a fold in the
harness near the end with the white
ground wire. Push the fold into a heavy
socket (or tape any heavy object to the
fold). Feed the weight into the tongue and
let gravity pull the harness through. Remove the weight.
13. Attach the two rubber stand-up
feet to the rear of the frame. Tighten
until snug only.
14. Cut two slits for the bolts to pass through the
decal. Attach the retractable tongue retainer bracket
to the inside of the rear frame crossmember with a
washer under the bolt head.
16. Slide the rear end of the tongue into the retractable receiver box until the pin hole in the box
aligns with one of the 2 pin holes in the sides of the tongue. Pass the hitch pin through and install
the ring clip.
technical@maloneautoracks.com
800-295-0042 ext.215
16. Identify the hitch end of the tongue by the 3 holes on
the left (drivers) side and Install the wiring harness exten-
sion (with a plug at each end),through the tongue, leaving
enough excess at the front to reach the vehicle. NOTE:
MAKE SURE YOUR PLUG MATCHES THE VEHICLE
CONNECTION. IF NOT REVERSE YOUR WIRING
HARNESS NOW.
15. Mount the tongue slide stop to the inside center of the rear
cross member. Nuts on the inside, bolts and washers on the
outside.
14. Attach the two rubber stand-up feet to the
rear of the frame. Tighten until snug only
17. Slide the rear end of the tongue into the retractable receiver box until the pin in the box aligns
with one of the 2 pin holes in the side of the tongue. Pass the hitch pin through and install the ring
clip.
MPG460XT
800-295-0042 ext 206
technical@maloneautoracks.com
12
15. Install the wiring harness extension
through the tongue.
The easiest way is to let gravity pull the
harness through. Make a fold in the
harness near the end with the white
ground wire. Push the fold into a heavy
socket (or tape any heavy object to the
fold). Feed the weight into the tongue and
let gravity pull the harness through. Remove the weight.
13. Attach the two rubber stand-up
feet to the rear of the frame. Tighten
until snug only.
14. Cut two slits for the bolts to pass through the
decal. Attach the retractable tongue retainer bracket
to the inside of the rear frame crossmember with a
washer under the bolt head.
16. Slide the rear end of the tongue into the retractable receiver box until the pin hole in the box
aligns with one of the 2 pin holes in the sides of the tongue. Pass the hitch pin through and install
the ring clip.
MPG460XT
800-295-0042 ext 206
technical@maloneautoracks.com
12
15. Install the wiring harness extension
through the tongue.
The easiest way is to let gravity pull the
harness through. Make a fold in the
harness near the end with the white
ground wire. Push the fold into a heavy
socket (or tape any heavy object to the
fold). Feed the weight into the tongue and
let gravity pull the harness through. Remove the weight.
13. Attach the two rubber stand-up
feet to the rear of the frame. Tighten
until snug only.
14. Cut two slits for the bolts to pass through the
decal. Attach the retractable tongue retainer bracket
to the inside of the rear frame crossmember with a
washer under the bolt head.
16. Slide the rear end of the tongue into the retractable receiver box until the pin hole in the box
aligns with one of the 2 pin holes in the sides of the tongue. Pass the hitch pin through and install
the ring clip.