Malaguti Dune X 125 страница 96 Скачать руководство пользователя

Страница: 96 / 272

Dune 125 - Dune X 125 - Euro 4

Electrical system

ELE SYS - 96

Troubleshooting

Shorted to positive:



Disconnect the coil connector, turn the key to ON and activate the component through the

diagnostics instrument.



Verify the presence of voltage on the coil connector PIN 2: if present, restore the cabling,

otherwise replace the coil.

The circuit is open:



Carry out the check procedure of the coil and control unit connectors.



Verify continuity of the cabling between the coil and control unit: Coil PIN 2 - control unit PIN

1. In the absence of continuity restore the cabling.



Verify, with the key turned ON, the presence of voltage on the coil connector PIN 1. If no

voltage is read, verify the continuity of the cabling between coil and injection relay (No. 35

on the electrical circuit diagram): Coil PIN 1 - relay PIN 3.



If the above tests provided a positive result, the coil should be replaced.

Shorted to negative:



Disconnect the control unit connector and the coil connector.



Verify the coil connector PIN 2 ground insulation (or control unit connector PIN 1). Restore

the cabling if necessary.

Engine oil pressure sensor

Function

Notifies the instrument panel that the oil pressure

in the engine is sufficient.

Operation / Operating principle

The switch is normally closed (connects ECU sig-

nal to ground). At pressures above ... bar, the

switch opens.

Level in electrical circuit diagram:

Low fuel and oil pressure

Position:



on the vehicle: RH side, near the water

pump



connector: on the sensor

Electrical specifications: -

Pin out:

1. Voltage: 5 V

Содержание Dune X 125

















































































































































































































































































Результаты поиска

Содержание Dune X 125

Отзывы:

Похожие инструкции для Dune X 125

Бренды по названию

Популярные бренды

Malaguti Dune X 125, Руководство по обслуживанию станции

Результаты поиска

Содержание Dune X 125

Отзывы:

Похожие инструкции для Dune X 125

Бренды по названию

Популярные бренды