Malaguti Dune X 125 страница 89 Скачать руководство пользователя

Страница: 89 / 272

Dune 125 - Dune X 125 - Euro 4

Electrical system

ELE SYS - 89

ELECTRICAL ERRORS

Engine temperature sensor P0115

- open circuit or shorted to positive / shorted to negative.

Cause of error

Open circuit or short circuit to positive: interruption of the circuit or excessive voltage at PIN 13 of the

control unit connector.

Short circuit to negative: null voltage between PIN 13 and 15 of the control unit connector.

Troubleshooting

Open circuit:



Disconnect the connector of the control unit.



Measure the resistance value of the sensor at different temperatures between PIN 13 and

15.



Disconnect the sensor connector.



Verify continuity of the wiring harness between the sensor connector and the control unit

connector: Control unit PIN 13 - sensor PIN 3 and control unit PIN 15 - sensor PIN 1. If

necessary, restore the wiring harness.



If the wiring harness is intact but the sensor resistance value is incorrect, this means that

the sensor is faulty and must be replaced, otherwise proceed with the checks.

Short-circuit to positive:



With the sensor connector and the control unit disconnected, verify that the fault is shorted

with the battery positive of sensor connector PIN 3 (or control unit connector PIN 13) and

restore the cabling.

Short circuit to negative:



Disconnect the sensor connector.



Check the sensor connector PIN 3 ground insulation.



If there is no ground insulation restore the wiring harness.



If PIN 3 is insulated from the ground and the error persists, this means that there is a

probable fault in the control unit.

Содержание Dune X 125

















































































































































































































































































Результаты поиска

Содержание Dune X 125

Отзывы:

Похожие инструкции для Dune X 125

Бренды по названию

Популярные бренды

Malaguti Dune X 125, Руководство по обслуживанию станции

Результаты поиска

Содержание Dune X 125

Отзывы:

Похожие инструкции для Dune X 125

Бренды по названию

Популярные бренды