Malaguti Dune X 125 страница 102 Скачать руководство пользователя

Страница: 102 / 272

Dune 125 - Dune X 125 - Euro 4

Electrical system

ELE SYS - 102

1. Voltage 0 V with engine kill in STOP; 12V if engine kill in RUN (pink/yellow cable)

2. Always voltage 12 V (with key on) (red/yellow cable)

Diagnostic tool - Parameters and statuses



RUN/OFF Switch - (RUN-OFF)

Diagnosis

Engine does not start

Error cause



Possible malfunction

Troubleshooting



Disconnect the connector and check, with the switch set to RUN, that there is continuity

between the two grey/light blue and red/grey cables (sensor side); If not ok, replace the

sensor; if ok, check the connector; if not ok, restore the wiring harness; if ok, check, with key

set to ON, if there is voltage on Yellow/Red cable (wiring harness side). If not ok,restore the

wiring harness; if ok, check the red/yellow cable ground insulation (wiring harness side); If

there is continuity with ground connection, restore the wiring harness; if it is OK, set the key

to KEY OFF and check the engine control unit connector; if it is OK, replace the engine

control unit

Engine does not shut off with switch in "STOP"

Error cause



Possible malfunction

Troubleshooting



Disconnect the connector and verify, with the switch set to STOP, that there is continuity

between the two grey/light blue and red/grey cables (sensor side). If present, replace the

switch; if absent this means that, with the key ON, the pink/yellow cable shorts to positive;

if not OK, restore the wiring harness; if OK, replace the engine control unit

Connectors

ECU

Function

It manages injection/ignition, the system safety

checks and the self-diagnosis function. The con- trol

unit is Magneti Marelli MIU G3

Level in electrical circuit diagram

Diagnostics,

pre-configuration for BlueDash

Position



on the vehicle: under tank, by filter box



connector: on ECU with 34 PINs

Содержание Dune X 125

















































































































































































































































































Результаты поиска

Содержание Dune X 125

Отзывы:

Похожие инструкции для Dune X 125

Бренды по названию

Популярные бренды

Malaguti Dune X 125, Руководство по обслуживанию станции

Результаты поиска

Содержание Dune X 125

Отзывы:

Похожие инструкции для Dune X 125

Бренды по названию

Популярные бренды