Malaguti Dune X 125 Скачать руководство пользователя страница 9

Страница: 9 / 272

Dune 125 - Dune X 125 - Euro 4

Characteristics

CHAR - 9

BEFORE DISASSEMBLING COMPONENTS



Remove the dirt, mud, dust and foreign objects from the vehicle before disassembling com-

ponents. Wherever required, use the special tools designed for this vehicle.

DISASSEMBLING COMPONENTS



Do not loosen and/or tighten the screws and nuts using pliers or other tools, but always use

the specific wrench.



Mark the positions on all the connection joints (hoses, cables, etc.) before separating them

and identify them with different distinctive marks.



Each piece should be clearly marked in order to be identified during the installation phase.



Carefully clean and wash the disassembled components with detergents with a low flam-

mability grade.



Keep the coupled parts together because they have "adapted" to one another following

normal wear.



Some components must be used together or replaced entirely.



Keep away from heat sources.

REASSEMBLING COMPONENTS

CAUTION

BEARINGS MUST ROTATE FREELY, WITHOUT JAMMING AND/OR NOISE, OTHERWISE, THEY
NEED TO BE REPLACED.



Only use ORIGINAL Malaguti SPARE PARTS.



Comply with lubricant and consumables use guidelines.



Lubricate parts (whenever possible) before reassembling them.



When tightening nuts and screws, start either from the components with the largest diameter

or from the innermost components, proceeding diagonally. Tighten nuts and screws in suc-

cessive steps before applying the tightening torque.



Always replace self-locking nuts, washers, sealing rings, circlips, O-rings (OR), cotter pins

and screws with new parts if the thread is damaged.



When assembling the bearings, make sure to lubricate them well.



Check that each component is assembled correctly.



After a repair or routine maintenance, carry out pre-ride checks and test the vehicle on

private grounds or in an area with low traffic.



Clean all mating surfaces, oil seal rims and gaskets before refitting. Smear a thin layer of

lithium-based grease on the oil seal rims. Reassemble oil seals and bearings with the brand

or batch number facing outward (visible side).

ELECTRICAL CONNECTORS

Electric connectors must be disconnected as described below; failure to comply with this procedure

causes irreparable damage to both the connector and the wiring harness:

Press the relative safety clips, if applicable.

Содержание Dune X 125

















































































































































































































































































Результаты поиска

Содержание Dune X 125

Отзывы:

Бренды по названию

Популярные бренды

Malaguti Dune X 125, Руководство по обслуживанию станции

Результаты поиска

Содержание Dune X 125

Отзывы:

Бренды по названию

Популярные бренды